
The AirTAC SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X90-50 is a genuine double-acting COMPACT cylinder (Ø25mm bore) whose extend end-position is set by an external M8×1.25 adjustment screw. You can dial the stroke anywhere from 40 to 90 mm on the machine — no shims, no part change.
The AirTAC SDAJ25X90-50 is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M8x1.25) screw, you can dial the extend end-position anywhere between 40 and 90 mm directly on the machine, avoiding shims or part swaps. Retract remains full length, and the mechanical stop does not alter the pneumatic force.
The short riveted body minimises axial mounting depth where round-body or profile cylinders will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which is not an adjustable air cushion. This specific SKU lacks a piston magnet, so it cannot host reed or electronic switches without upgrading to the -S variant.
| Model | Airtac SDAJ12~25 Adjustable Ultra-Thin Cylinder SDAJ25X90-50 |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø25 mm |
| Max stroke | 90 mm |
| Adjustable range | 40 – 90 mm |
| Adjuster thread (R) | M8×1.25 |
| Port size | M5×0.8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M5×0.8 F / M8×1.25 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 50 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 206 N | 206 N |
| 0.7 MPa | 289 N | — |
| Max (@1.0 MPa) | 42 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 25 | Bore size in mm. |
| ×90 | Maximum stroke length in mm. |
| -50 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 40 to 90 mm during machine changeovers to accommodate different part heights without machining new spacers.
Sweep through trial positions on a test rig to find the optimal engagement point, then lock the M8x1.25 adjuster screw once the cycle is proven.
Choose this model when your fixture requires on-site stroke tuning across a 50 mm window.
Confirm the bore, 90 mm maximum stroke, 50 mm adjust window, and M5x0.8 port. The rod end is female M5x0.8 (use male M8x1.25 if specified with a B suffix). Remember that a plain cylinder does not hold position on air loss or valve centring; the piston drifts and the fixed bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ25 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj25-adjustable-cylinder
Quick checklist
The theoretical maximum push is 50 kgf at 1.0 MPa. The adjuster screw changes the stop position, not these force values.
Turning the R (M8x1.25) screw shortens the extend stroke by up to 50 mm, giving a usable range of 40 to 90 mm. The screw is a mechanical stop, not a mid-stroke lock. If air is lost, the cylinder will drift; use an external rod lock or pilot-operated check valve to hold a load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.