
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X100-20SB is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 80 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X100-20SB is a double-acting compact cylinder featuring a 63 mm bore and a male-thread piston rod (M18x1.5). An external R (M16x1.5) adjuster screw lets you dial the extend stop down from the 100 mm maximum to 80 mm directly on the machine, eliminating the need for shims or part swaps during changeovers.
This riveted-body design saves significant axial mounting depth where a larger profile cylinder cannot fit, while operating at speeds between 30 and 500 mm/s. The unit includes a built-in piston magnet for AirTAC reed or electronic switches, and relies on a fixed NBR bumper at each end to decelerate the stroke. The bumper is not an adjustable air cushion, and the mechanical stop does not function as a mid-stroke lock.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X100-20SB |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 100 mm |
| Adjustable range | 80 – 100 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dialing the extend stop from 80 to 100 mm allows operators to fine-tune clamping depth on varying part heights without machining custom spacers.
Rapid product line changeovers benefit from the external R screw adjustment, repositioning the extend endpoint in seconds rather than swapping cylinders.
Choose this specific configuration when you need on-site stroke tuning between 80 and 100 mm. It is specified with a PT1/4 port, a male M18x1.5 rod end, and an integrated magnet for position sensing. Remember that a plain compact cylinder does not hold its load if air pressure is lost or the valve is centered; the piston will drift. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 2182.1 N and pull to 1962.2 N. The theoretical maximum push is 318 kgf at 1.0 MPa.
The R (M16x1.5) screw mechanically shortens the extend stroke by up to 20 mm, allowing usable endpoints between 80 and 100 mm without changing the output force. The included -S magnet enables position detection using AirTAC reed or electronic solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.