
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X110-40B is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 70 to 110 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X110-40B is a compact double-acting double-rod cylinder built for on-site extend positioning. An external M16x1.5 adjuster screw lets you dial the forward stop anywhere between 70 and 110 mm without swapping shims or parts, while the retract stroke remains full length.
This variant features a male M18x1.5 piston rod thread and lacks a piston magnet. The short riveted body minimizes axial mounting depth where larger profile or round-body units will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X110-40B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 110 mm |
| Adjustable range | 70 – 110 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×110 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the M16x1.5 screw to set the extend precisely between 70 and 110 mm for varying raw casting widths on a milling line without swapping tooling.
Fine-tune the forward stop on the factory floor during product family changeovers, relying on the 40 mm adjustment window to hit new target coordinates.
Choose this specific model if your fixture requires precise 70-110 mm extend tuning during frequent changeovers.
Confirm your parameters: 63 mm bore, 110 mm max stroke, 40 mm adjust window, PT1/4 air port, and a male M18x1.5 rod end. Because this SKU omits the -S magnet, it cannot accept reed or electronic switches. Note that the fixed bumper only decelerates the stroke end; a plain cylinder drifts on air loss, so integrate an external rod lock or pilot-operated check valve for load holding.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
Operating pressure is 0.15-1.0 MPa, proof pressure is 1.5 MPa, and speed ranges from 30-500 mm/s.
Turning the external R (M16x1.5) screw mechanically shortens the extend end-position from the 110 mm maximum down to 70 mm. The adjuster sets the physical stop and does not alter force. It is not a mid-stroke lock; the cylinder will drift on air loss, so use an external rod lock for load holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.