
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X130-20S is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 110 to 130 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X130-20S is a compact double-acting double-rod cylinder featuring an external adjustable extend stop. By turning the R (M16x1.5) screw, you can precisely shorten the forward stroke on-site across a 110-130 mm window without swapping shims or components. This on-machine tuning accelerates commissioning and simplifies changeovers. The retract motion remains full length.
The short riveted body minimizes axial mounting depth where larger profile cylinders cannot fit. End-of-travel deceleration relies on a fixed NBR bumper, which is not an adjustable air cushion. This unit includes a built-in piston magnet for position sensing.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X130-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 130 mm |
| Adjustable range | 110 – 130 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×130 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 110 and 130 mm to find the exact cutting contact point on custom fixtures without fabricating new spacers.
Set precise upper travel limits for lifting a 79.4 kg payload, relying on the mechanical stop rather than risking overshoot from valve timing.
When sizing this model, evaluate both neighboring bores. This 63 mm bore provides a theoretical maximum of 318 kgf at 1.0 MPa.
Choose this specific configuration if your fixture requires exact forward positioning between 110 and 130 mm during setup. Confirm your parameters: 63 mm bore, 130 mm maximum stroke, 20 mm adjust window, PT1/4 port, female M10x1.5 rod thread, and the -S magnet for reed or electronic switches. Remember that a plain cylinder does not hold position on air loss; the fixed bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
The theoretical maximum push is 318 kgf at 1.0 MPa.
The M16x1.5 adjuster screw mechanically shortens the extend end position from the 130 mm maximum down to 110 mm. The -S code denotes a built-in piston magnet compatible with AirTAC reed or electronic solid-state switches for position detection.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.