
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X35-20S is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 15 to 35 mm on the machine — no shims, no part change.
The SDAJ63X35-20S is a compact double-acting double-rod cylinder engineered with an external adjustable extend stop. By turning the R (M16x1.5) screw, you shorten the forward stroke on-site across a 15 to 35 mm window, avoiding shims or part swaps during machine commissioning.
This riveted-body design saves axial mounting depth where round-body alternatives will not fit, operating at 30-500 mm/s. The unit relies on a fixed NBR bumper at each end to decelerate the stroke, which is not an adjustable air cushion. Equipped with a built-in piston magnet (-S), it supports AirTAC reed or electronic solid-state switches for precise end-position sensing.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X35-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 35 mm |
| Adjustable range | 15 – 35 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×35 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Adjust the mechanical stop without shims to accommodate different box depths, relying on the fixed NBR bumper to absorb the 30-500 mm/s approach impact.
Set precise lower endpoints for a 79.4 kg vertical lift payload, using the M16x1.5 adjuster screw to fine-tune the drop distance safely.
When sizing this 63 mm bore actuator, evaluate your force requirements bidirectionally.
Choose this specific configuration if your fixture requires on-site stroke tuning between 15 and 35 mm. It features a PT1/4 port, a 20 mm piston rod, female M10x1.5 rod-end threads, and the -S magnet for switch integration. Remember that a plain cylinder does not hold its load on air loss or valve centring; the fixed bumper only decelerates near the end. For secure load holding without live pressure, install an external rod lock or pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 2182.1 N and pull to 1962.2 N. The theoretical maximum push force is 318 kgf at 1.0 MPa.
The M16x1.5 adjuster screw mechanically shortens the extend stroke from the 35 mm maximum down to 15 mm without altering the force output. The included -S magnet works with AirTAC reed or electronic solid-state switches for position detection.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.