
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X40-10S is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 30 to 40 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X40-10S is a double-acting, double-rod compact cylinder featuring an external adjustable extend stop. By turning the R (M16x1.5) screw, you can dial the extend position down from the 40mm maximum to 30mm directly on the machine, avoiding part changes during setup.
The short riveted body saves valuable axial mounting depth where larger profile or round-body units will not fit. End-of-stroke deceleration is handled by a fixed NBR bumper, which absorbs shock but is not an adjustable air cushion. Equipped with a built-in magnet (-S), this unit supports AirTAC reed or electronic solid-state switches mounted in the body sensor grooves for precise position confirmation.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X40-10S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 40 mm |
| Adjustable range | 30 – 40 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 10 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×40 | Maximum stroke length in mm. |
| -10 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dials the extend stop between 30 and 40mm to secure raw castings of varying widths against a fixed backstop without swapping out actuator hardware.
Speeds up product family changeovers on a shared fixture by allowing operators to fine-tune the 1558.6 N extend stroke on-site using the M16x1.5 adjuster.
Sets a precise lower mechanical stop for a 79.4 kg lift profile, ensuring the load bottoms out consistently while relying on the fixed NBR bumper to absorb end shock.
Choose this specific 30-40mm adjustable model for lines requiring frequent changeovers or trial positioning.
Confirm the 63mm bore, 40mm stroke, 10mm window, PT1/4 port, and female M10x1.5 rod-end thread suit your spatial envelope. Note that a plain cylinder does not hold its load if air pressure drops or the valve is centred; the piston drifts and the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
The theoretical maximum push is 318 kgf at 1.0 MPa.
The external R (M16x1.5) screw shortens the extend stroke by up to 10mm, yielding a usable extend range of 30-40mm without changing force. The built-in -S magnet works with AirTAC reed or electronic solid-state switches for position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.