
The AirTAC SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X50-40S is a genuine double-acting COMPACT cylinder (Ø63mm bore) whose extend end-position is set by an external M16×1.5 adjustment screw. You can dial the stroke anywhere from 10 to 50 mm on the machine — no shims, no part change.
The AirTAC SDAJ63X50-40S is a compact double-acting double-rod cylinder engineered for on-site extend-position tuning. A side-mounted M16x1.5 adjustment screw lets you dial the outward stop anywhere between 10 and 50 mm, eliminating the need for shims or part swaps during machine commissioning.
This 63 mm bore variant features a short riveted body that minimizes axial mounting depth where a round-body or profile cylinder will not fit. It integrates a fixed NBR bumper at each end to decelerate the stroke end, though this is not an adjustable air cushion. Equipped with a built-in piston magnet, the unit supports AirTAC reed or electronic switches for precise end-of-travel signaling.
| Model | Airtac SDAJ50~63 Adjustable Ultra-Thin Cylinder SDAJ63X50-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø63 mm |
| Max stroke | 50 mm |
| Adjustable range | 10 – 50 mm |
| Adjuster thread (R) | M16×1.5 |
| Port size | PT1/4 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M10×1.5 F / M18×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1402 N | 1402 N |
| 0.7 MPa | 1962 N | — |
| Max (@1.0 MPa) | 286 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 63 | Bore size in mm. |
| ×50 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop between 10 and 50 mm to secure varying raw castings without swapping fixture hardware.
Set precise mechanical end positions for diverter gates, using the fixed NBR bumper to absorb the kinetic impact.
When sizing this actuator, compare its output against adjacent bores. Choose this specific unit if your fixture requires frequent changeovers or trial positioning within the 10 to 50 mm range.
Confirm your parameters before ordering: a 63 mm bore, 50 mm maximum stroke, 40 mm adjust window, and PT1/4 air port. The rod measures 20 mm with a female M10x1.5 end thread. The -S suffix indicates the internal magnet is present for sensing. Remember that a plain cylinder does not hold its load on air loss or when a valve is centered; the piston drifts and the fixed bumper only decelerates near the end. For load holding without live pressure, install an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ63 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj63-adjustable-cylinder
Quick checklist
The theoretical maximum is 318 kgf at 1.0 MPa.
The M16x1.5 screw shortens the extend stop by up to 40 mm, giving a usable range of 10 to 50 mm. It sets the stop position without changing force. The -S suffix means a built-in magnet is included for AirTAC reed or electronic switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.