
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X100-30B is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 70 to 100 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X100-30B is a compact double-acting double-rod cylinder featuring an on-machine extend stop. A M20x1.5 adjuster screw lets you dial the outward stroke anywhere between 70 and 100 mm without swapping shims or components.
Designed to save axial mounting depth, the short riveted body fits where round-body or profile cylinders cannot. This specific SKU includes a male M22x1.5 piston rod end and uses a PT3/8 air port. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion, and this base configuration ships without a piston magnet, meaning magnetic switches cannot be fitted unless you specify the -S variant.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X100-30B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 100 mm |
| Adjustable range | 70 – 100 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 30 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×100 | Maximum stroke length in mm. |
| -30 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the 70-100 mm extend stop to set precise pressing depths for different bearing sizes on a single fixture, avoiding part changes during product changeover.
Fine-tune the clamping reach during machine commissioning to prevent over-travel on delicate castings, relying on the fixed NBR bumper to absorb the final stop impact.
When sizing this 80 mm bore actuator, evaluate your force needs against its neighbours.
Choose this model if your fixture requires precise outward positioning during setup or frequent changeovers, as the 30 mm adjustment window allows fine-tuning directly on the machine. Verify your system requires a male M22x1.5 rod thread and a PT3/8 port. Remember that a standard cylinder does not hold a load if air pressure drops or the valve is centred; the piston will drift and the fixed bumper only decelerates near the end of the stroke. For suspended or vertical loads, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj80-adjustable-cylinder
Quick checklist
The theoretical maximum push force is 513 kgf at 1.0 MPa.
The external M20x1.5 screw acts as a mechanical stop, shortening the extend stroke anywhere between 70 and 100 mm. It does not alter the output force and is not a mid-stroke lock; the cylinder cannot hold a load without continuous air pressure.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.