
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X15-20B is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 0 to 15 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X15-20B is a compact double-acting double-rod cylinder featuring an external M20x1.5 adjuster screw that dials the extend stop down to a 0-15 mm window on-site. The short riveted body saves valuable axial mounting depth where a larger profile cylinder will not fit.
This specific SKU uses a male M22x1.5 piston rod thread and PT3/8 air ports. End-of-travel deceleration is handled by a fixed NBR bumper rather than an adjustable air cushion. It carries no piston magnet, so position sensing is not supported on this base unit.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X15-20B |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 15 mm |
| Adjustable range | 0 – 15 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×15 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Allows operators to fine-tune the 0-15 mm extend stop on the machine to achieve the exact seating force for inserting heavy bearing assemblies without swapping shims.
Fits within tight machine frames where axial space is restricted, using the compact riveted body to deliver high clamping force in a minimal footprint.
Choose this configuration if your fixture requires on-site extend tuning to dial in a precise 0-15 mm reach. Note that a plain cylinder does not hold its load if air pressure is lost or the valve is centred; the piston will drift and the fixed bumper only decelerates near the end of travel. For secure load holding without live pressure, integrate an external rod lock or a pilot-operated check valve. Confirm your requirements for an 80 mm bore, 15 mm stroke, 20 mm window, PT3/8 port, no magnet, and the male M22x1.5 rod thread.
AirtacDistr lists every SDAJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj80-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 3518.6 N and pull to 3175 N. The theoretical maximum push force is 513 kgf at 1.0 MPa.
Turning the external M20x1.5 screw shortens the extend stroke by up to 20 mm, allowing you to set the end position anywhere within a 0-15 mm usable range. This screw acts only as a mechanical stop and does not alter the output force. The cylinder cannot hold a load on air loss; you must use an external rod lock or pilot-operated check valve for position holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.