
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X30-20S is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 10 to 30 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X30-20S is a compact double-acting double-rod cylinder engineered for high-force applications where exact end-positioning must be dialed in on the machine. An external M20x1.5 adjuster screw modifies the extend stop from 10 to 30 mm without requiring shims or part swaps.
Built with a space-saving riveted body, this model fits tight axial envelopes while housing a 25 mm piston rod and a PT3/8 port. It includes a fixed NBR bumper at each end to decelerate the stroke, though this is not an adjustable air cushion. The built-in magnet (-S) supports AirTAC reed or electronic switches for precise end-of-stroke sensing in automated setups.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X30-20S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 30 mm |
| Adjustable range | 10 – 30 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 20 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×30 | Maximum stroke length in mm. |
| -20 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fine-tune the 10-30 mm extend stop during heavy press changeovers to accommodate varying material thicknesses without swapping mechanical spacers.
Set precise downward travel for a 128 kg vertical lift actuator, relying on the M20x1.5 screw to establish a hard mechanical stop at the exact lower datum.
Fit high-force clamping into a narrow machine footprint using the short riveted body, adjusting the jaw extension on the factory floor to suit different fixture heights.
When sizing this unit, evaluate your force requirements against neighboring bores. Choose this specific configuration if your fixture design requires on-site stroke tuning within the 10 to 30 mm range.
Confirm the 80 mm bore, 30 mm maximum stroke, 20 mm adjustment window, PT3/8 port, built-in magnet (S), and female M14x1.5 rod-end thread meet your envelope constraints. Note that a plain cylinder does not hold position or load when air is lost or the valve is centered; the fixed bumper only decelerates near the end of travel. For load holding without live pressure, integrate an external rod lock or a pilot-operated check valve.
AirtacDistr lists every SDAJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj80-adjustable-cylinder
Quick checklist
It operates between 0.15 and 1.0 MPa at speeds of 30-500 mm/s.
The M20x1.5 external screw shortens the extend stop by up to 20 mm, yielding a usable extend range of 10 to 30 mm; retract remains full stroke. The built-in S magnet works with AirTAC reed or electronic switches for position sensing, while the fixed NBR bumper decelerates the stroke end.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.