
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X45-40S is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 5 to 45 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X45-40S is a compact double-acting double-rod cylinder featuring an external M20x1.5 adjustment screw that dials the extend stop from 5 to 45 mm directly on your equipment. Retract travel stays at the full 45 mm regardless of the extend setting.
Its short riveted body saves valuable axial mounting depth where larger profile or round-body units will not fit, while a fixed NBR bumper at each end absorbs end-of-stroke shock. This specific unit includes a built-in piston magnet (-S) for direct mounting of AirTAC reed or electronic solid-state switches along the body grooves.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X45-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 45 mm |
| Adjustable range | 5 – 45 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×45 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Fit the compact riveted body into tight machine frames where axial length is restricted, adjusting the extend endpoint on the fly during new product introduction runs.
Operators requiring frequent changeovers or trial positioning benefit most from this adjustability. Confirm your parameters: 80 mm bore, 45 mm max stroke, 40 mm window, PT3/8 air port, female M14x1.5 rod-end thread, and the -S magnet for sensing. Note that the fixed NBR bumper only decelerates the stroke end; it does not lock the piston. If you must hold a load during air loss or valve centering, install an external rod lock or pilot-operated check valve, as the adjuster is strictly a mechanical stop.
AirtacDistr lists every SDAJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj80-adjustable-cylinder
Quick checklist
This 80 mm bore cylinder uses a PT3/8 air port.
Turning the external R (M20x1.5) screw shortens the extend stroke by up to 40 mm, yielding a usable 5 to 45 mm range without changing parts. The -S code denotes a built-in piston magnet designed to trigger AirTAC reed or electronic solid-state switches.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.