
The AirTAC SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X80-40S is a genuine double-acting COMPACT cylinder (Ø80mm bore) whose extend end-position is set by an external M20×1.5 adjustment screw. You can dial the stroke anywhere from 40 to 80 mm on the machine — no shims, no part change.
The AirTAC SDAJ80X80-40S is a compact double-acting double-rod cylinder built for on-site extend tuning. An external M20x1.5 adjuster screw lets you dial the forward stop anywhere between 40 and 80 mm without swapping shims or parts.
Its short riveted body significantly cuts axial mounting depth where a larger profile or round-body unit will not fit. The unit carries a built-in piston magnet for AirTAC reed or electronic solid-state switches. End-of-travel energy is managed by a fixed NBR bumper that decelerates the load, though it is not an adjustable air cushion or a locking brake.
| Model | Airtac SDAJ80~100 Adjustable Super Slim Cylinder SDAJ80X80-40S |
|---|---|
| Series | SDAJ compact adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Max stroke | 80 mm |
| Adjustable range | 40 – 80 mm |
| Adjuster thread (R) | M20×1.5 |
| Port size | PT3/8 |
| Acting type | Double acting |
|---|---|
| Rod end thread | M14×1.5 F / M22×1.5 male (B) |
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed NBR bumper (both ends) |
The adjustment screw shortens the extend stroke by up to 40 mm. SDAJ is a double-rod cylinder. Specifications follow the official AirTAC SDAJ datasheet.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 2268 N | 2268 N |
| 0.7 MPa | 3175 N | — |
| Max (@1.0 MPa) | 463 kgf | |
SDAJ is double-rod: the rear rod that carries the stroke adjuster passes through the rear cover, so both piston faces lose rod area. Push is shown at the annular-area value (conservative), lower than a single-rod SDA push of the same bore. Actual usable force is lower than theoretical due to friction.
| SDAJ | Compact double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×80 | Maximum stroke length in mm. |
| -40 | Adjustable window (10/20/30/40/50/75/100 mm). |
| S / B | S = magnet; B = male-thread rod (both optional). |
Thread: PT standard. Related SDA-family variants: SDA (fixed stroke), SDAD (double rod), SSA/STA (single acting), SDAT (duplex), SDAW (duplex-end).
Dial the extend stop from 80 mm down to 40 mm to test insertion depths on thick steel bushings without machining new spacers.
Stepping down to the SDAJ63 provides 1558.6 N, while stepping up to the SDAJ100 yields 3927 N. Choose this specific 80 mm model when your setup requires heavy pushing but still demands the physical footprint savings of a compact body. The PT3/8 port and 25 mm rod handle substantial flow and guide loads.
This configuration is ideal for machinery needing frequent changeovers or trial positioning, as the R screw allows rapid extend shortening from 80 mm down to 40 mm. Note that a plain cylinder does not hold its load on air loss or when the valve is centred; the piston drifts and the fixed bumper only decelerates near the end. For a held load, specify an external rod lock or a pilot-operated check valve. Confirm the 80 mm stroke, 40 mm window, PT3/8 port, built-in magnet, and female M14x1.5 rod thread for your assembly.
AirtacDistr lists every SDAJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sdaj80-adjustable-cylinder
Quick checklist
At 0.7 MPa, push increases to 3518.6 N. The theoretical maximum push is 513 kgf at 1.0 MPa.
The M20x1.5 R screw shortens the extend stop by up to 40 mm, giving a usable 40 to 80 mm forward range. The included S magnet enables position sensing with AirTAC reed or electronic switches. The screw is a mechanical stop, not a mid-stroke lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.