
The AirTAC SEJ Adjustable Cylinder SEJ125X125-50 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 50mm window, so this Ø125mm unit covers an effective stroke of 75–125mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ125X125-50 is a double-acting, double-rod ISO 15552 profile cylinder featuring a 50 mm adjustable stroke window. By turning the stop screw on the back rod, you dial the retract end from 75 mm up to the full 125 mm, letting you fine-tune the machine stop without swapping hardware.
This extruded aluminum profile cylinder omits external tie rods and integrates field-adjustable air cushions at both ends to decelerate heavy loads near the stroke limits. It carries a PT1/2 port, a Ø32 mm rod with an M27x2 thread, and operates at 30-500 mm/s. Note this SKU lacks a magnet, so it will not trigger CMSE or DMSE position sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ125X125-50 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø125 mm |
| Nominal stroke | 125 mm |
| Adjustment window | 50 mm (75–125 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M27×2 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 50mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 5734 N |
| 0.7 MPa | 8027 N |
| Max (@1.0 MPa) | 1169 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 125 | Bore size in mm. |
| ×125 | Nominal stroke length in mm. |
| -50 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Leverage the 5734 N both-way force and dial the retract stroke from 75 to 125 mm to precisely trial-set press die heights during changeovers without machining new spacers.
Use the symmetrical double-rod output to halt heavy pallets on a conveyor, adjusting the stop position up to 50 mm to accommodate varying pallet footprints on the fly.
Fine-tune the electrode landing position on a large automated welder; the 50 mm window allows exact calibration of the end-stop against the workpiece during commissioning.
Confirm the 50 mm adjustment window covers your required end-position range. If you need less force, stepping down to the 80 mm bore yields 2268 N both ways at 0.5 MPa; stepping up is not possible as 125 mm is the largest available. If your end position never varies, a fixed-stroke SED125x125 provides the same twin-rod stability without the adjustment mechanism. Remember that the adjustable cushion and stop screw decelerate the load but do not lock it; a plain SEJ will not hold position on air loss, so add an external rod lock for fail-safe holding. When replacing an ISO 15552 unit, match the 125 mm bore, 125 mm nominal stroke, PT1/2 port, and your mounting choice from the available Basic, FA, LB, TC, FTC, TCM1, or TCM2 kits.
AirtacDistr lists every SEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-sej125-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 50 mm window, giving you an effective stroke range of 75 to 125 mm. You set the exact end-position on the machine and lock the screw in place, eliminating the need for different length cylinders during fine-tuning.
Because it is a double-rod cylinder, force is equal in both directions: 5734 N at 0.5 MPa, 8028 N at 0.7 MPa, and a maximum of 1169 kgf at 1.0 MPa. The operating speed for this 125 mm bore is 30-500 mm/s.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.