
The AirTAC SEJ Adjustable Cylinder SEJ125X25-10S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 10mm window, so this Ø125mm unit covers an effective stroke of 15–25mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ125X25-10S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 10mm adjustable stroke window. A rod exits both ends, yielding identical annulus areas so the output force is perfectly equal in both directions. You can expect 5734 N of thrust and pull each way at 0.5 MPa.
A stop screw on the back rod lets you mechanically dial the retract end position down from the 25mm nominal stroke to a 15mm minimum. Because this is a 125mm bore, the heavy 32mm rod and M27x2 threading provide high rigidity against side loads, and the integrated -S magnet enables precise end-of-travel detection using CMSE reed or DMSE electronic sensors.
| Model | Airtac SEJ Adjustable Cylinder SEJ125X25-10S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø125 mm |
| Nominal stroke | 25 mm |
| Adjustment window | 10 mm (15–25 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M27×2 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 10mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 5734 N |
| 0.7 MPa | 8027 N |
| Max (@1.0 MPa) | 1169 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 125 | Bore size in mm. |
| ×25 | Nominal stroke length in mm. |
| -10 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Delivering 5734 N each way at 0.5 MPa, use the 10mm retract dial to set exact 15-25mm closure depths on heavy stamping dies without swapping hardware.
Tune the precise engagement point of an automotive clutch assembly fixture; the equal both-way force ensures consistent 1169 kgf max clamping without directional drift.
Adjust the mechanical stop for varying steel plate thicknesses in a conveyor lift, leveraging the rigid 32mm double-rod to resist severe deflection during impact.
This 10mm adjustment window is ideal for fine-tuning short, heavy-duty end positions, giving an effective stroke range of 15-25mm. If your process requires less force, stepping down to the 80mm bore yields 2268 N both ways at 0.5 MPa, whereas stepping up is unavailable as 125mm is the largest standard SEJ size. If you do not need variable stops, a fixed-stroke SED cylinder offers the same twin-rod power in a shorter body.
For any fail-safe load holding on air loss, note that this cylinder does not lock the rod internally; you must pair it with an external BSED rod lock. The adjustable air cushions at both ends decelerate the mass near the stroke limits but do not serve as a mechanical brake. Ensure your setup uses the PT1/2 port and matches the ISO 15552 mounting dimensions (Basic, FA, LB, TC, FTC, TCM1, or TCM2).
AirtacDistr lists every SEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-sej125-adjustable-cylinder
Quick checklist
A stop screw on the back rod mechanically shortens the retract stroke within a 10mm window. This means your effective stroke can be dialed anywhere from 15mm up to the full 25mm, then locked in place for precise machine commissioning.
Because the rod exits both ends, force is equal in both directions: 5734 N at 0.5 MPa, 8028 N at 0.7 MPa, and a maximum of 1169 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.