
The AirTAC SEJ Adjustable Cylinder SEJ125X400-100S is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø125mm unit covers an effective stroke of 300–400mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ125X400-100S is a double-acting, double-rod ISO 15552 profile cylinder featuring a 100mm adjustable stroke window. A rod exits both ends, meaning the annular area is identical in both directions for an equal force of 5734 N each way at 0.5 MPa. The effective retract stroke dials from 300mm up to 400mm.
You mechanically set the end position via a stop screw on the back rod, then lock it after dialing in the exact machine stop. It carries a -S magnet for CMSE or DMSE electronic sensors, uses PT1/2 ports, and relies on field-adjustable air cushions at both ends to decelerate heavy loads near the stroke end.
| Model | Airtac SEJ Adjustable Cylinder SEJ125X400-100S |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø125 mm |
| Nominal stroke | 400 mm |
| Adjustment window | 100 mm (300–400 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M27×2 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 5734 N |
| 0.7 MPa | 8027 N |
| Max (@1.0 MPa) | 1169 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 125 | Bore size in mm. |
| ×400 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 400mm stroke down by 100mm to precisely set the press contact point on varying material stacks, utilizing the 5734 N both-way force for consistent forming.
Adjust the retract end-stop on the fly for different bending depths without swapping hardware, locking the back-rod screw once the 300-400mm position is set.
Reposition the stroke end to match differing pallet heights on a packaging line, using the equal push/pull force to smoothly shift heavy fixtures.
Verify the 100mm adjustment window covers your positioning range, allowing the 125mm bore to dial the retract end anywhere from 300mm to 400mm. If 8028 N at 0.7 MPa is excessive, step down to the 100mm bore for 5153 N; if you need more power, no larger standard SEJ bore exists. If the exact end position never changes, a fixed-stroke SED saves length and cost. For any fail-safe hold on air loss, add an external rod lock like BSED, as the stop screw and cushion only set the mechanical end and decelerate, not lock position. Because this unit runs a 400mm stroke, external guide rails are strongly recommended to manage rod side loads and prevent binding.
AirtacDistr lists every SEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-sej125-adjustable-cylinder
Quick checklist
A stop screw on the rear rod mechanically shortens the retract stroke over a 100mm window. You can dial the effective stroke anywhere from 300mm up to the nominal 400mm, then lock the screw for precise commissioning.
Because it is a double-rod cylinder, force is equal in both directions: 5734 N at 0.5 MPa, 8028 N at 0.7 MPa, and a maximum of 1169 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.