
The AirTAC SEJ Adjustable Cylinder SEJ125X50-20SN is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 20mm window, so this Ø125mm unit covers an effective stroke of 30–50mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ125X50-20SN is a double-acting, double-rod ISO 15552 profile cylinder. A rod exits both ends, yielding identical annulus areas so output force is equal in both directions at 5734 N each way at 0.5 MPa. It includes a magnet for position sensing.
A mechanical stop screw on the back rod provides a 20 mm adjustment window, letting you dial the retract stroke down from 50 mm to an effective 30 mm. This allows precise on-machine end-position tuning without swapping hardware. The NBR seals handle standard temperatures, while adjustable air cushions at both ends manage deceleration.
| Model | Airtac SEJ Adjustable Cylinder SEJ125X50-20SN |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø125 mm |
| Nominal stroke | 50 mm |
| Adjustment window | 20 mm (30–50 mm) |
| Configuration | Double rod, double acting |
| Port size | PT1/2 |
| Rod thread | M27×2 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 40 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 20mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 5734 N |
| 0.7 MPa | 8027 N |
| Max (@1.0 MPa) | 1169 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 125 | Bore size in mm. |
| ×50 | Nominal stroke length in mm. |
| -20 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 20 mm retract window to match material thickness precisely. The 125 mm bore delivers 5734 N both ways, holding heavy gauge stops rigidly during forming.
Fine-tune the clamping end position on the machine without changing hardware. Equal push and pull forces ensure consistent clamping pressure throughout the stroke.
Adjust the stop position for different pallet heights across a 30 to 50 mm range. The built-in magnet works with DMSE sensors to confirm retraction.
Verify the 20 mm adjustment window covers your required 30-50 mm retract range. If you need less force, the 100 mm bore provides 3681 N both ways at 0.5 MPa; if you need more, this 125 mm bore is the largest standard size offering 8028 N at 0.7 MPa. If exact stroke positioning is not needed, a fixed-stroke SED cylinder is simpler.
For holding position on air loss, note this cylinder does not lock; you need an external rod lock. The PT1/2 ports, M27x2 rod thread, and basic mounting match ISO 15552 dimensional profiles. At 50 mm stroke, side loads are minimal, but external guides are recommended for heavy loads.
AirtacDistr lists every SEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-sej125-adjustable-cylinder
Quick checklist
A stop screw on the rear rod lets you mechanically shorten the retract stroke. The 20 mm adjustment window allows an effective stroke range of 30 to 50 mm. You set the exact end position and lock the screw, avoiding hardware swaps.
Because a rod exits both ends, force is identical in both directions. It generates 5734 N at 0.5 MPa, 8028 N at 0.7 MPa, and a maximum of 1169 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.