
The AirTAC SEJ Adjustable Cylinder SEJ80X300-100 is a genuine double-acting ISO 15552 double-rod cylinder with a mechanically ADJUSTABLE stroke: a back-rod stop screw lets you fine-tune the retract end over a 100mm window, so this Ø80mm unit covers an effective stroke of 200–300mm without changing cylinders. Force is equal in both directions.
The AirTAC SEJ80X300-100 is a double-acting, double-rod ISO 15552 profile cylinder with a 100 mm adjustable retract window, yielding an effective stroke range of 200 to 300 mm. A rod exits both ends, creating identical annular areas so output force is perfectly balanced at 2268 N each way at 0.5 MPa. You dial in the exact end position using a stop screw on the back rod, then lock it down—ideal for dialing in a precise stop during machine commissioning without machining new hardware.
This extruded aluminum barrel omits external tie rods and carries field-adjustable air cushions at both ends to decelerate the load near stroke extremes. Because this 300 mm stroke exceeds the 300 mm threshold, external guide rails should be used to prevent side-loading damage to the rod seals. This SKU has no -S magnet, so it will not host CMSE or DMSE position sensors without modification.
| Model | Airtac SEJ Adjustable Cylinder SEJ80X300-100 |
|---|---|
| Series | SEJ ISO 15552 adjustable-stroke cylinder |
| Bore size | Ø80 mm |
| Nominal stroke | 300 mm |
| Adjustment window | 100 mm (200–300 mm) |
| Configuration | Double rod, double acting |
| Port size | PT3/8 |
| Rod thread | M20×1.5 |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 36 mm |
Specifications follow the official AirTAC SEJ datasheet and ISO 15552 / VDMA 24562 dimensions. The adjustment screw shortens the retract end only; do not exceed the 100mm window. Port options: PT (standard) / G (BSPP).
| Pressure | Force (both directions) |
|---|---|
| 0.5 MPa | 2268 N |
| 0.7 MPa | 3175 N |
| Max (@1.0 MPa) | 463 kgf |
A rod exits both ends, so extend and retract force are identical. Actual usable force is lower than theoretical; size with a safety margin.
| SEJ | ISO 15552 double-rod double-acting cylinder with adjustable stroke. |
|---|---|
| 80 | Bore size in mm. |
| ×300 | Nominal stroke length in mm. |
| -100 | Adjustment stroke window in mm (options: 10/20/30/40/50/75/100). |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting (SEJ): Basic, LB, FA, TC, FTC, TCM1, TCM2. Related: SED (double rod, fixed stroke), SE (single rod).
Dial the 100 mm retract window to hit varied sheet metal bend depths precisely, leveraging the 3175 N both-way force at 0.7 MPa to push and pull the stop gauge without asymmetric drift.
Adjust the effective stroke between 200 and 300 mm to accommodate different pallet heights on a machining center, using the equal push/pull force to shift heavy fixtures smoothly.
Fine-tune the exact engagement point of a 300 mm stroke test rig during commissioning, locking the back-rod stop screw once the exact 80 mm bore contact point is found.
Confirm the 100 mm adjustment window covers your required end-position variance, allowing you to shift the retract stop anywhere from 200 to 300 mm. If you need less fine-tune range, a fixed-stroke SED80X300 is enough. For sizing both ways: stepping down to the 63 mm bore drops your both-way force to 1402 N at 0.5 MPa, while stepping up to the 100 mm bore raises it to 3681 N at 0.5 MPa. Remember, the adjustable air cushion only decelerates the load; it does not hold position on air loss. For fail-safe holding, specify a BSED or an external rod lock. Match your ISO 15552 replacement by verifying the PT3/8 port, M20x1.5 rod thread, and mounting choice (Basic, FA, LB, TC, FTC, TCM1, or TCM2—FB/CA/CB/CR are unavailable).
AirtacDistr lists every SEJ80 order code with its price on one page at https://airtacdistr.com/products/airtac-sej80-adjustable-cylinder
Quick checklist
A stop screw on the back rod lets you mechanically shorten the retract stroke by up to 100 mm. The effective stroke range is 200 to 300 mm, allowing you to fine-tune the end position on the machine without changing hardware.
Because the rod exits both ends, force is equal in both directions: 2268 N at 0.5 MPa, 3175 N at 0.7 MPa, with a maximum of 463 kgf at 1.0 MPa.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.