Airtac ACED Double-acting Compact Cylinder ACED100X200
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED100X200 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø100mm bore and 200mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke200 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED100X200
A heavy-duty double acting compact cylinder built to ISO 21287, the ACED100X200 pushes a 100 mm bore through a 200 mm stroke with a rod leaving BOTH covers. Because each side sees the rod-side area, output is a matched 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa in either direction - no push/pull imbalance to compensate for in your force budget.
The through-rod resists rotation and side load and gives a symmetric mount, and the rear rod can carry a sensor flag or a second tooling plate. At 0.5 MPa that 3769.9 N rating works out to roughly 384 kg of raw lift, so planning around half of it lets the cylinder raise about 192 kg vertically with margin to spare. The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, a fixed TPU bumper decelerates both ends of travel, and speed runs 30-500 mm/s across 0.15-1.0 MPa (22-145 psi).
Airtac ACED Double-acting Compact Cylinder ACED100X200 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED100X200 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 3770 N |
| 0.7 MPa | 5278 N |
| Max (@1.0 MPa) | 769 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED100X200
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 100 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED100X200 Is Used
Pallet stamping station
A 200 mm stroke reaches deep into a pallet-nesting press, and the 3769.9 N both-ways force stamps batch codes identically on the advance and return legs.
Battery tray lift-assist gantry
The symmetric through-rod carries a lift frame from both ends, raising battery trays of about 190 kg vertically at 0.5 MPa with a 2:1 margin.
Heavy carton pusher on a case line
Mounted on LB feet beside a conveyor, the rear rod drives a flag for end-of-stroke confirmation while the front rod squares 25 kg cases at up to 500 mm/s.
Is the Airtac ACED Double-acting Compact Cylinder ACED100X200 the Right Cylinder?
At this force class the nearest smaller step is the 80 mm bore at 2356.2 N at 0.5 MPa; if your load needs more than about 2262 N of usable work (0.6 of this bore's rating), the 100 mm is the right pick, and the 125 mm bore at 5890.5 N covers heavier presses. The 200 mm stroke sits well inside the 300 mm maximum standard stroke for this bore, so it ships as a standard build. Remember this is not a position holder: if the load must stay put on air loss, add a rod lock or pilot check valve. Choose FA/FB flange, LB foot or FTC brackets plus I/Y rod knuckles, and order the -S code only if you need the optional magnet for CMSE / DMSE switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED100X200 FAQ
Yes - the double-rod design means both strokes use the rod-side area, so output is equal either way: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa, peaking at 768.8 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with proof pressure of 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/4" port suits this 100 mm bore.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body cuts mounting length by about 50% versus an ISO 15552 profile cylinder, with an S45C hard-chrome-plated 20 mm rod and female M12x1.75 thread. Fixed TPU bumpers at each end absorb end-of-stroke shock. FA/FB flanges, LB foot and FTC brackets bolt to the standard face, and the magnet is the optional -S code - without it no CMSE or DMSE switch can be fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED100X200
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.