Airtac ACED Double-acting Compact Cylinder ACED100X300SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED100X300SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø100mm bore and 300mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke300 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED100X300SB
A double acting compact cylinder built to ISO 21287, the ACED100X300SB pushes a 100 mm bore through a 300 mm stroke with a rod leaving both covers. Because each side works on the rod-side area, output is identical in both directions: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa. The hard-anodized aluminium body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, so it slots into presses, gantries and guarding where a full-length body cannot fit.
The through-rod resists rotation and side load, and the rear rod can carry a sensor flag or a second tooling plate. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches mount directly in the body slots, and the B code gives a male rod thread. With 3769.9 N at 0.5 MPa, plan on roughly 2262 N of usable work, which lifts about 192 kg vertically with a 2:1 margin. Speed range is 30-500 mm/s and the fixed TPU bumper at each end absorbs end-of-stroke shock.
Airtac ACED Double-acting Compact Cylinder ACED100X300SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED100X300SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 300 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 3770 N |
| 0.7 MPa | 5278 N |
| Max (@1.0 MPa) | 769 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED100X300SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 100 | Bore size in mm. |
| ×300 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED100X300SB Is Used
Press-fit stamping station
The 3769.9 N both-ways force at 0.5 MPa presses bearings or bushings into housings on an automotive assembly line, with the return stroke delivering equal force for part ejection.
Pallet lift-and-lower module
A 300 mm stroke lifting about 192 kg vertically with a 2:1 margin raises and lowers totes between conveyor levels in a warehouse transfer unit.
Reciprocating spray carriage
The symmetric through-rod drives a paint or wash nozzle carriage back and forth at 30-500 mm/s, with the rear rod carrying a CMSE switch target for stroke feedback.
Is the Airtac ACED Double-acting Compact Cylinder ACED100X300SB the Right Cylinder?
At 100 mm bore this sits near the top of the ACED range: step down to the 80 mm bore (2356.2 N at 0.5 MPa) for lighter clamping, or up to the 125 mm bore (5890.5 N) when the load demands it. The 300 mm stroke matches the maximum standard stroke for this bore, so no made-to-order length is needed. Remember the piston drifts if air is lost - add a rod lock or pilot check valve for a held load. FA/FB flange, LB foot and FTC brackets bolt to the ISO 21287 face, and I/Y rod knuckles suit the male-threaded rod.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED100X300SB FAQ
Yes. As a double-rod cylinder, both strokes act on the rod-side area, so force is equal pushing and pulling: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa. At the full 1.0 MPa rating the peak is 768.8 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, on air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FA/FB flange, LB foot or FTC brackets bolt straight to its face. This version includes the -S magnet, so CMSE / DMSE reed or solid-state switches can be clipped into the body slots for end-of-stroke detection. The fixed TPU bumper at each end decelerates the piston; it does not hold or brake a load, so use a rod lock or pilot check where position must be kept.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED100X300SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.