Airtac ACED Double-acting Compact Cylinder ACED100X80SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED100X80SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø100mm bore and 80mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ100 mm
- Stroke80 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED100X80SB
A double acting compact cylinder built to ISO 21287, the ACED100X80SB pushes a 100 mm bore through an 80 mm stroke with a rod leaving BOTH covers, so thrust is identical on each stroke: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa. The S in the code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped onto the body for end-of-stroke signalling, and the B gives a male thread on each 20 mm rod end.
The hard-anodized aluminium body with an S45C hard-chrome plated rod runs at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s and -20 to +70 C, with a fixed TPU bumper at each end. Because the short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, this 100 mm bore fits gantries and press fixtures that cannot swallow a full-length body. As a planning figure, treat roughly 2260 N (about 230 kg of push) as the usable working output at 0.5 MPa rather than the full rating.
Airtac ACED Double-acting Compact Cylinder ACED100X80SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED100X80SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø100 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø100mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 3770 N |
| 0.7 MPa | 5278 N |
| Max (@1.0 MPa) | 769 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED100X80SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 100 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED100X80SB Is Used
Gantry press fixture
The 3769.9 N symmetric thrust at 0.5 MPa swages or stakes aluminium brackets on a machining line, with the 80 mm stroke sized for quick in-and-out tooling moves.
Reciprocating transfer arm
A rod on each cover lets the rear rod drive a flag past a DMSE switch while the front rod pushes pallets, giving equal 5277.9 N force at 0.7 MPa in both travel directions.
Vertical clamp on a weld cell
The through-rod resists rotation when pressing steel door panels down, and the compact body drops into a tight weld gantry where an ISO 15552 profile cylinder would be twice as long.
Is the Airtac ACED Double-acting Compact Cylinder ACED100X80SB the Right Cylinder?
At this force class the nearest smaller step is the 80 mm bore at 2356.2 N per direction at 0.5 MPa, while the next size up is the 125 mm bore at 5890.5 N - pick 100 mm when your fixture needs roughly 3.7 kN without the bulk. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve for a held load. FA/FB flange, LB foot and FTC brackets plus I and Y rod knuckles bolt to the ISO 21287 face, and the through-rod resists rotation while the rear rod can carry a sensor flag. This unit already carries the -S magnet; order plain ACED codes without S when no switching is needed.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED100X80SB FAQ
Both directions are identical because a rod exits each cover and both strokes use the rod-side area: 3769.9 N at 0.5 MPa and 5277.9 N at 0.7 MPa, with a maximum of 768.8 kgf at 1.0 MPa. For sizing, keep real work near 2260 N (about 230 kg equivalent) at 0.5 MPa, and note the piston will drift if air pressure is lost - use a rod lock or pilot check where a load must stay put.
S means the optional -S magnet is fitted on this unit, so CMSE or DMSE reed or solid-state switches mount directly on the body slots (plain ACED codes ship without a magnet). B means a male thread on each 20 mm rod end, with a 1/4" PT port on the 100 mm bore. The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke energy.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED100X80SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.