Airtac ACED Double-acting Compact Cylinder ACED16X75S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED16X75S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø16mm bore and 75mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ16 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM4×0.7
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED16X75S
A double acting compact cylinder with a rod leaving both covers, the ACED16X75S delivers 75.4 N in each direction at 0.5 MPa because both strokes work on the rod-side area. The 16 mm bore runs on 0.15-1.0 MPa (22-145 psi) of filtered air at 30-500 mm/s, and the through-rod resists rotation while the rear rod can carry a sensor flag.
The hard-anodized aluminium body with an S45C hard-chrome rod keeps the ISO 21287 footprint short, saving roughly 50% of the mounting length of an ISO 15552 profile cylinder, which matters in slim fixtures and guarding. Fixed TPU bumpers sit at both ends, and the fitted -S magnet lets CMSE or DMSE switches report position. For sizing: 75.4 N at 0.5 MPa supports about 45 N of real work, or lifts roughly 3.8 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED16X75S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED16X75S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø16 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M4×0.7 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 75 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø16mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 75 N |
| 0.7 MPa | 106 N |
| Max (@1.0 MPa) | 15 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED16X75S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 16 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED16X75S Is Used
Position-verified small-part clamps
The fitted -S magnet and CMSE/DMSE switches confirm clamp state on electronics assembly fixtures, while the 75.4 N symmetric force grips PCB carriers evenly from either side.
Reciprocating guide rails
A rod on each cover gives a symmetric mount for light slide gates on packaging lines; the through-rod resists rotation at speeds from 30 to 500 mm/s.
Compact pick-and-place lifts
The short ISO 21287 body tucks under gantry plates where a full-length profile cylinder will not fit, lifting parts of about 3.8 kg with a 2:1 vertical margin.
Is the Airtac ACED Double-acting Compact Cylinder ACED16X75S the Right Cylinder?
At 75.4 N per side (0.5 MPa) this bore sits between the 12 mm ACED (42.4 N) and the 20 mm ACED (117.8 N); step up if your clamp or lift needs more than about 45 N of usable force. The 75 mm stroke is the maximum standard stroke for bore 16, so no made-to-order build is required. FA/FB flange, LB foot and FTC brackets, plus I/Y rod knuckles, bolt to the ISO 21287 face. A plain double-rod cylinder drifts when air is lost, so add a rod lock or pilot check if the load must stay put.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED16X75S FAQ
Output is equal both ways because the double rod exposes the rod-side area on each stroke: 75.4 N at 0.5 MPa, 105.6 N at 0.7 MPa, with a maximum of 15.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, air filtered to 40 um.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, S45C hard-chrome plated rod, threaded covers and fixed TPU bumpers at both ends; the body saves about 50% of the mounting length of an ISO 15552 profile cylinder. The -S magnet is already fitted on this model, so CMSE or DMSE reed or solid-state switches can be mounted directly in the body slots. Rod end is a female M4x0.7 thread and the port is M5x0.8.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED16X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.