Airtac ACED Double-acting Compact Cylinder ACED25X35
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED25X35 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø25mm bore and 35mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ25 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED25X35
The ACED25X35 is a double acting compact cylinder built to ISO 21287 with a piston rod leaving BOTH covers, so the 25 mm bore delivers the same 206.2 N at 0.5 MPa (288.6 N at 0.7 MPa) on every stroke - the rod-side area works in both directions. The through-rod resists rotation and light side load, and the rear rod stub can carry a sensor flag or a second tooling plate. Air supply is 0.15-1.0 MPa (22-145 psi), speed range 30-500 mm/s.
The hard-anodized aluminium body with a hard-chrome plated S45C rod runs a fixed TPU bumper at each end for end-of-stroke deceleration. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so this 35 mm stroke unit slots into tight fixtures and sliding guards. At 0.5 MPa plan on roughly 124 N of usable push force, which lifts about 10 kg vertically with a 2:1 margin. FA/FB flange, LB foot and FTC brackets bolt straight to the standard face.
Airtac ACED Double-acting Compact Cylinder ACED25X35 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED25X35 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED25X35
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 25 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED25X35 Is Used
Small-parts press fitting
The symmetric 206.2 N output at 0.5 MPa suits pressing dowel pins or bushings into aluminium housings on a bench fixture, where equal force on approach and return keeps the part seated.
Pick-and-place shuttle
With a rod on both covers, the 35 mm stroke can drive a slide from either face on a PCB tray indexer, and the rear rod stub carries a flag for a proximity sensor.
Lid lift on packaging heads
About 10 kg of vertical lift capacity with a 2:1 margin at 0.5 MPa raises a small guarding lid or filler-head cover, with the TPU bumper softening each end of travel.
Is the Airtac ACED Double-acting Compact Cylinder ACED25X35 the Right Cylinder?
Size between the ACED20X35 (117.8 N at 0.5 MPa) and the ACED32X35 (345.6 N at 0.5 MPa): pick this 25 mm bore when your clamp or transfer job needs about 206 N both ways. The 35 mm stroke sits well inside the 150 mm maximum standard stroke for this bore, so it ships as a catalogue item. Remember the piston drifts when air is lost - add a rod lock or pilot check valve if the load must stay put. The rod end is female M6x1.0 and the port is M5x0.8 PT; order the -S code if you later want CMSE / DMSE switches, because this version carries no magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED25X35 FAQ
Because a rod exits both covers, force is equal in both directions: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa on every stroke, with a maximum of 42.0 kgf at 1.0 MPa. In practice plan on roughly 124 N for real work at 0.5 MPa, which lifts about 10 kg vertically with a 2:1 margin. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed runs 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FA/FB flange, LB foot and FTC brackets bolt straight to the standard face. Sensing needs the optional -S magnet code: order ACED25X35S and CMSE / DMSE switches will clamp into the body slots. This base version has no magnet fitted, and the fixed TPU bumpers at both ends only soften end-of-stroke travel.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED25X35
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.