Airtac ACED Double-acting Compact Cylinder ACED25X80SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED25X80SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø25mm bore and 80mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ25 mm
- Stroke80 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED25X80SB
A double acting compact cylinder built to ISO 21287, the ACED25X80SB has a piston rod leaving both covers, so the 25 mm bore delivers the same 206.2 N at 0.5 MPa (288.6 N at 0.7 MPa) on every stroke - the rod-side area works in both directions. The through-rod resists rotation and light side load, and the rear rod can carry a sensor flag. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be clipped straight onto the body slots.
The short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs, guards and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the S45C hard-chrome-plated 10 mm rod with male thread (the B code) suits standard rod knuckles. At 0.5 MPa the usable working force is roughly 124 N, which lifts about 10 kg vertically with a sensible margin.
Airtac ACED Double-acting Compact Cylinder ACED25X80SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED25X80SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED25X80SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 25 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED25X80SB Is Used
Reciprocating transfer slides
The through-rod gives an identical 206.2 N push and pull at 0.5 MPa, so a pick-and-place slide on a small-parts assembly line accelerates the same in both directions at 30-500 mm/s.
Position-checked clamping fixture
With the -S magnet fitted, CMSE or DMSE switches confirm clamp-open and clamp-close on a machining fixture, and the male rod thread takes an I or Y knuckle for the clamp point.
Compact press / staking head
About 124 N of practical working force at 0.5 MPa stakes terminals or presses bearings in electronics sub-assemblies where the short body must fit under a low gantry.
Is the Airtac ACED Double-acting Compact Cylinder ACED25X80SB the Right Cylinder?
Size both ways: if 206.2 N at 0.5 MPa is more than the job needs, the ACED20X80SB gives 117.8 N in the same compact envelope; if the load is heavier, step up to the ACED32X80SB at 345.6 N. The 80 mm stroke sits well inside the 150 mm maximum standard stroke for bore 25, so it ships as a catalogue item. Ports are M5x0.8, and FA/FB flange, LB foot or FTC brackets bolt to the ISO 21287 face. Remember that a plain double-rod cylinder drifts when air is lost - add a rod lock or pilot check if the load must stay put.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED25X80SB FAQ
Because a rod exits both covers, force is equal in both directions: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa on every stroke, peaking at 42.0 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures, and FA/FB flange, LB foot or FTC brackets bolt to the standard face. This model carries the -S magnet, so CMSE / DMSE switches mount in the body slots for end-of-stroke signalling. A fixed TPU bumper at each end absorbs end-of-stroke energy; the cylinder never holds position on its own if air is lost.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED25X80SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.