Airtac ACED Double-acting Compact Cylinder ACED25X90
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED25X90 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø25mm bore and 90mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ25 mm
- Stroke90 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED25X90
A double acting compact cylinder built to ISO 21287, the ACED25X90 pushes a 25 mm piston through a 90 mm stroke with a rod leaving BOTH covers. Because each side sees the rod-side area, output is identical either way: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa. Air supply is 0.15-1.0 MPa (22-145 psi), speed runs 30-500 mm/s, and the fluid must be air filtered to 40 um.
The through-rod resists rotation and light side load, and the rear rod is a handy carrier for a sensor flag on a gate or slider. The hard-anodized aluminium body with an S45C hard-chrome plated rod saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures. At 0.5 MPa the 206.2 N rating is about 21 kgf, so plan on lifting roughly 10 kg vertically with a 2:1 margin. A fixed TPU bumper at each end takes the end-of-stroke hit; it does not hold position, so add a rod lock or pilot check if the load must stay put when air drops.
Airtac ACED Double-acting Compact Cylinder ACED25X90 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED25X90 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 150 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED25X90
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 25 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED25X90 Is Used
Symmetric part ejector
The equal 206.2 N output in both directions lets a jig-and-fixture builder eject a machined aluminium blank from its nest on the forward stroke and retract the pusher with identical force, no spring return needed.
Conveyor gate diverter
A packaging line uses the through-rod as a rigid guide for a 90 mm divert gate that swings small cartons between two lanes at 30-500 mm/s, with the rear rod doubling as a flag mount for a position sensor when the -S magnet is ordered.
Lab sample press
A testing bench presses sample vials into a sealing station with about 10 kg of vertical lift capacity at a 2:1 margin, the compact short body fitting inside a guarded enclosure where a full-length profile cylinder cannot.
Is the Airtac ACED Double-acting Compact Cylinder ACED25X90 the Right Cylinder?
At 206.2 N per direction at 0.5 MPa, this 25 mm bore sits between the 20 mm size (117.8 N) and the 32 mm size (345.6 N) - step down for lighter clamps, up if you need 345 N. The 90 mm stroke is well inside the 150 mm standard limit for bore 25, so no made-to-order build is needed. Ports are M5x0.8 and the rod ends in a female M6x1.0 thread. This code has no magnet: order the -S version if you want CMSE / DMSE switch detection. FA/FB flanges, LB feet, CA/CB clevises and I/Y rod knuckles bolt straight to the ISO 21287 face.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED25X90 FAQ
It is a double-rod cylinder, so force is the same pushing and pulling: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, both taken on the rod-side area. Peak output at 1.0 MPa is 42.0 kgf. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed spans 30-500 mm/s.
The ISO 21287 short body is hard-anodized aluminium with threaded covers and a fixed TPU bumper at each end, cutting mounting length by about 50% versus an ISO 15552 profile cylinder. Sensing is not fitted on this code: the magnet is the optional -S version, which accepts CMSE / DMSE switches. Mounting brackets (FA/FB flange, LB foot, CA/CB clevis, FTC) and I/Y rod knuckles attach to the standard ISO 21287 face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED25X90
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.