Airtac ACED Double-acting Compact Cylinder ACED32X175S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED32X175S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø32mm bore and 175mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke175 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED32X175S
A double acting, double-rod compact cylinder built to ISO 21287, the ACED32X175S pushes a 32 mm bore through a 175 mm stroke with a rod leaving both covers. Because each side works on the rod-side area, output is identical in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The through-rod resists rotation and modest side load, and the rear rod can carry a sensor flag or a second tooling plate. The hard-anodized aluminium body with an S45C hard-chrome plated rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding where a full-length body will not fit. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the fitted -S magnet lets you add CMSE or DMSE switches for end-of-stroke and mid-stroke signals. At 0.5 MPa the 345.6 N rating translates to roughly 35 kgf, so plan on lifting about 17 kg vertically with a 2:1 margin, or budget around 207 N for real work.
Airtac ACED Double-acting Compact Cylinder ACED32X175S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED32X175S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 175 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED32X175S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 32 | Bore size in mm. |
| ×175 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED32X175S Is Used
Reciprocating glue-head carriage
The through-rod drives a hot-glue head on a packaging line with equal 345.6 N force on both the dispense and return strokes, keeping cycle timing symmetric at 30-500 mm/s.
Gantry pick-and-place with position feedback
With the -S magnet fitted, CMSE or DMSE switches signal retract, extend and intermediate positions on a small-parts gantry, while the rear rod carries a second fixture plate.
Press-fit of bushings into housings
About 207 N of usable work at 0.5 MPa suits light press-fitting of small bushings and dowels in electronics assembly, with the 175 mm stroke clearing tall fixtures.
Is the Airtac ACED Double-acting Compact Cylinder ACED32X175S the Right Cylinder?
Size both ways: if 345.6 N at 0.5 MPa is more than the job needs, the bore 25 ACED gives 206.2 N; if the load needs more, step up to bore 40 for 571.8 N. The 175 mm stroke sits inside the 200 mm maximum standard stroke for bore 32, so no made-to-order build is required. This model carries the -S magnet, so CMSE or DMSE switches can be clamped straight into the body slots. Remember that a plain double-rod cylinder drifts when air is lost - for a held load, pair it with a rod lock or pilot check valve. FA/FB flange, LB foot and FTC brackets plus I and Y rod knuckles bolt to the standard ISO 21287 face, and the female M8x1.25 rod thread accepts standard tooling studs.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED32X175S FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so force is equal either way: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, freeing space in tight guarding. This model carries the optional -S magnet, so CMSE or DMSE reed or solid-state switches clamp into the body slots for position signals. A fixed TPU bumper at each end absorbs end-of-stroke energy, and FA/FB flange, LB foot or FTC mounting bolts to the standard face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED32X175S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.