Airtac ACED Double-acting Compact Cylinder ACED32X200
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED32X200 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø32mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED32X200
A double acting compact cylinder built to ISO 21287, the ACED32X200 runs a 32 mm bore with a 200 mm stroke and a 12 mm rod exiting BOTH covers. Because each side works on the rod-side area, output is identical in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The hard-anodized aluminium body carries fixed TPU bumpers at each end, and the S45C hard-chrome-plated rod resists wear on long duty cycles.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding where a full-length body will not fit. The through-rod also resists rotation and side load, and the rear rod can carry a sensor flag. As a working figure, plan on roughly 207 N of usable thrust at 0.5 MPa, which corresponds to lifting about 17 kg vertically with a 2:1 margin. Air supply is 0.15-1.0 MPa (22-145 psi), speed range 30-500 mm/s, and the 1/8" port depends on the bore.
Airtac ACED Double-acting Compact Cylinder ACED32X200 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED32X200 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED32X200
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED32X200 Is Used
Push-pull fixture clamping
Equal 345.6 N force in both directions lets one ACED32X200 clamp and then retract a nesting fixture on a CNC jig with the same rated thrust each way.
Bidirectional parts diverter
The 200 mm stroke swings or pushes product between two conveyor lanes, with the rear rod doubling as a mount point for a position flag.
Test rig load cycling
Symmetric 483.8 N at 0.7 MPa and 30-500 mm/s speed suit repetitive press or fatigue test stations where identical force is needed on both strokes.
Is the Airtac ACED Double-acting Compact Cylinder ACED32X200 the Right Cylinder?
At 345.6 N per direction at 0.5 MPa, this bore sits between the 25 mm (206.2 N) and 40 mm (571.8 N) options - step down for lighter clamping, up if your part mass grows. The 200 mm stroke is the maximum standard stroke for a 32 mm bore, so no made-to-order build is needed. Note that with no air applied the piston drifts freely; if the load must stay put on air loss, pair it with a rod lock or pilot check valve. FA/FB flange, LB foot and FTC brackets plus I/Y rod knuckles bolt straight to the ISO 21287 face. This unit has no magnet fitted - order the -S code if you need CMSE / DMSE switch detection.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED32X200 FAQ
Yes - the double-rod design puts a 12 mm rod through both covers, so both strokes work on the rod-side area. Output is 345.6 N at 0.5 MPa, 483.8 N at 0.7 MPa, and up to 70.5 kgf (705 N class) at the 1.0 MPa maximum, identical push and pull. Operating pressure is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof rating.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and fixed TPU bumpers absorb end-of-stroke shock at both ends. Sensing is not included as standard: this model has no magnet, so order the -S version to enable CMSE / DMSE reed or solid-state switches in the body's magnet slots. Mounting brackets (FA/FB flange, LB foot, FTC) and I/Y rod knuckles attach directly to the standard face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED32X200
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.