Airtac ACED Double-acting Compact Cylinder ACED32X200S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED32X200S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø32mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED32X200S
A double acting, double-rod compact cylinder built to ISO 21287, the ACED32X200S pushes a 12 mm hard-chrome rod out of BOTH covers, so thrust is identical on every stroke: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, in either direction. The 200 mm stroke sits right at the 200 mm maximum standard stroke for the 32 mm bore, and the short body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, letting it slide into tight guarding and gantry frames.
Because a rod exits each end, the through-rod resists rotation and side load and gives you a symmetric mount, with the rear rod free to carry a sensor flag. The hard-anodized aluminium body pairs with an S45C piston rod, fixed TPU bumpers absorb end-of-stroke shock at both ends, and the fitted -S magnet means CMSE / DMSE switches can be clipped onto the body slot for end-position detection. Running 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s, the 345.6 N rating works out to a practical vertical lift of about 17 kg with a 2:1 margin (345.6 / 9.81, halved), so match parts under that weight.
Airtac ACED Double-acting Compact Cylinder ACED32X200S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED32X200S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED32X200S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 32 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED32X200S Is Used
Reciprocating test rig carriage
The equal 345.6 N thrust in both directions drives a laboratory durability-test carriage back and forth over the full 200 mm travel, with CMSE switches marking each end via the fitted magnet.
Twin-sided ejection on a press jig
Front and rear rods eject finished aluminium housings from a machining jig alternately, the through-rod keeping the tooling aligned where a single-rod cylinder would twist.
Bidirectional pusher on a packaging line
One cylinder diverts cartons left or right on a conveyor, since the identical rod-side force whichever way it fires gives repeatable push at 30-500 mm/s.
Is the Airtac ACED Double-acting Compact Cylinder ACED32X200S the Right Cylinder?
At 345.6 N @0.5 MPa this 32 mm bore covers medium-duty clamping and transfer; step down to the 25 mm bore (206.2 N) for lighter pick-and-place, or up to the 40 mm bore (571.8 N) when the load grows. Remember the force is the same pushing and pulling, since both strokes act on the rod-side area. It will not hold position if air is lost - add a rod lock or pilot check valve for a suspended load. FA/FB flanges, LB feet and I/Y rod knuckles bolt straight to the ISO 21287 face, and the -S magnet on this model accepts CMSE / DMSE switches; the female M8x1.25 rod thread and 1/8" PT ports keep plumbing standard.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED32X200S FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so force is equal either way: 345.6 N at 0.5 MPa, 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow machine frames, and FA/FB flange, LB foot and I/Y knuckle hardware bolts straight to the standard face. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches mount in the body slot for position feedback. A fixed TPU bumper at each end absorbs end-of-stroke impact, and the female M8x1.25 rod thread suits standard tooling.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED32X200S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.