Airtac ACED Double-acting Compact Cylinder ACED32X70B
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED32X70B is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø32mm bore and 70mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke70 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED32X70B
A double acting compact cylinder built to ISO 21287, the ACED32X70B runs a 32 mm bore with a 70 mm stroke and a through rod that leaves both covers. Because each side of the piston sees the rod-side area, output is 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa in either direction - there is no weaker pull stroke. The male rod thread (B code) bolts straight to your tooling, and the 1/8" port suits standard PT fittings.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarded cells. In practice, plan on roughly 207 N of usable push at 0.5 MPa, which is about 21 kg - or size a vertical lift at around 17 kg with a 2:1 margin. A fixed TPU bumper at each end absorbs end-of-stroke shock, the hard-anodized aluminium body resists wear, and the S45C hard-chrome rod stands up to side load. Speed range is 30-500 mm/s over 0.15-1.0 MPa (22-145 psi).
Airtac ACED Double-acting Compact Cylinder ACED32X70B Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED32X70B |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED32X70B
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 32 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED32X70B Is Used
Stamping date codes on cartons
The 70 mm stroke reaches a print head across a conveyor gap, and the equal 345.6 N force both ways retracts the head as crisply as it extends, keeping ink marks consistent.
Reciprocating test rig actuator
A through rod on both ends lets a fatigue test fixture cycle a sample symmetrically at 30-500 mm/s, with the rear rod doubling as a position-flag carrier when the -S magnet is ordered.
Lift-and-lower ejector on a packaging line
With about 17 kg of vertical lift capacity at a 2:1 margin, the double rod guides a reject pusher square through a guide bush without rotating under load.
Is the Airtac ACED Double-acting Compact Cylinder ACED32X70B the Right Cylinder?
At 345.6 N per direction, this bore sits between the 25 mm size (206.2 N at 0.5 MPa) and the 40 mm size (571.8 N at 0.5 MPa) - step down for lighter clamps, up for heavier presses. The through rod resists rotation and lets the rear rod carry a sensor flag or a symmetric mount. Note that with no air applied the piston drifts freely; for a held load add a rod lock or pilot check valve. Mounting brackets (FA/FB flange, LB foot, FTC) and I/Y rod knuckles bolt to the ISO 21287 face. Position feedback needs the optional -S magnet code with CMSE / DMSE switches - this model, ordered without S, carries no magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED32X70B FAQ
Output is equal in both directions because a rod exits each cover: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. For real work, budget about 207 N (roughly 21 kg of push) at 0.5 MPa, or about 17 kg of vertical lift with a 2:1 safety margin.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow fixtures. Switches are not fitted as standard: order the -S code to get the optional magnet, then CMSE or DMSE switches sense position along the body slots. This ACED32X70B (no S) has no magnet, so no sensor can be mounted. A fixed TPU bumper at each end absorbs end-of-stroke shock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED32X70B
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.