Airtac ACED Double-acting Compact Cylinder ACED32X70S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED32X70S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø32mm bore and 70mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke70 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED32X70S
A double acting compact cylinder built to ISO 21287, the ACED32X70S pushes a 32 mm bore through a 70 mm stroke with a piston rod leaving BOTH covers. Because each side works on the rod-side area, output is identical in either direction: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The through-rod resists rotation and modest side load, and the rear rod end can carry a sensor flag while the front does the work.
The hard-anodized aluminium body with an S45C hard-chrome rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, and -20 to +70 C, with a fixed TPU bumper at each end. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding. Practical sizing: keep real work near 207 N (about 0.6 of the rating), and expect roughly 17 kg of vertical lift at a 2:1 margin. This -S model carries the optional magnet, so CMSE / DMSE switches mount directly on the body slots.
Airtac ACED Double-acting Compact Cylinder ACED32X70S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED32X70S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED32X70S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 32 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED32X70S Is Used
Fixture clamping on CNC pallets
The symmetric through-rod clamps a machined aluminium housing from both sides in a pallet changer, with 345.6 N per direction holding the part square during a facing cut.
Pusher on a bottling line
A rear rod end carries a flag for a DMSE switch (magnet fitted on this -S model), confirming each 70 mm push that nudges bottles across a transfer plate at up to 500 mm/s.
Slide transfer in electronics assembly
Equal force both ways moves a PCB tray between two nests, and the compact body saves roughly half the mounting length of an ISO 15552 profile cylinder inside the tight gantry frame.
Is the Airtac ACED Double-acting Compact Cylinder ACED32X70S the Right Cylinder?
At 345.6 N per direction, this bore suits clamping and positioning where a 12 mm rod must survive both strokes. Step down to a 25 mm bore (206.2 N) for lighter fixtures, or up to a 40 mm bore (571.8 N) for heavier presses. The 70 mm stroke sits well inside the 200 mm maximum standard stroke for bore 32. Remember the piston drifts if air is lost - add a rod lock or pilot check for held loads. Bolt on FA/FB flanges, LB feet or FTC brackets, and since the -S magnet is fitted, CMSE / DMSE switches can be added without reordering.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED32X70S FAQ
It is a double-rod cylinder, so force is EQUAL both ways: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa on each stroke, with a peak of 70.5 kgf at 1.0 MPa. Both strokes use the rod-side area because a 12 mm rod exits each cover.
It is an ISO 21287 compact cylinder whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end. Magnet slots run along the body, and this -S version carries the optional magnet, so CMSE / DMSE reed or solid-state switches mount directly; FA/FB flange, LB foot and FTC brackets bolt to the standard face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED32X70S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.