Airtac ACED Double-acting Compact Cylinder ACED32X90
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED32X90 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø32mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ32 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED32X90
The ACED32X90 is a double acting, double-rod compact cylinder built to ISO 21287: a 32 mm bore with 90 mm of stroke and a 12 mm rod leaving both covers, so the output force is identical on the extend and retract strokes. At 0.5 MPa it delivers 345.6 N either way, and 483.8 N at 0.7 MPa. The hard-anodized aluminium body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, which is why it drops into tight jigs and guarded stations a full-length body cannot fit.
Because the rod passes through both ends, the piston resists rotation and side load and the rear rod can carry a sensor flag or a second tooling plate. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the two-way piston seal stores grease for long service. Running on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), it cycles at 30-500 mm/s between -20 and +70 C. In practice, plan on roughly 207 N of usable work at 0.5 MPa, which lifts about 18 kg vertically with a 2:1 margin. The female M8x1.25 rod thread and 1/8" ports suit standard fittings; the optional -S magnet enables CMSE / DMSE switches.
Airtac ACED Double-acting Compact Cylinder ACED32X90 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED32X90 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED32X90
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 32 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED32X90 Is Used
Symmetric jig clamping
The equal 345.6 N force on both strokes lets one ACED32X90 press a machined aluminium bracket into a drill jig and retract it with identical force, keeping clamp pressure consistent across the cycle.
Two-position gate flagging
On a packaging line indexing cartons, the rear rod of the through-rod design carries a flag plate; with the optional -S magnet and DMSE switches the controller confirms both end positions without extra hardware.
Compact lift-and-lower station
A 90 mm stroke lifting about 18 kg of fixture weight inside a guarded assembly gantry, where the short ISO 21287 body fits the 100 mm envelope an ISO 15552 profile cylinder cannot.
Is the Airtac ACED Double-acting Compact Cylinder ACED32X90 the Right Cylinder?
Size both ways: the ACED25X90 gives 206.2 N at 0.5 MPa if your load is lighter, while the ACED40X90 reaches 571.8 N if you need more push. This 32 mm model sits in the middle at 345.6 N both directions. Remember the piston drifts if air is lost, so add a rod lock or pilot check for a held load. Bolt it down with FA or FB flanges, LB feet or FTC brackets, and add I or Y rod knuckles on the through-rod. Order the -S code only if you need CMSE / DMSE position switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED32X90 FAQ
Output is equal in both directions because a rod exits each cover: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa on both strokes, with a peak of 70.5 kgf at 1.0 MPa. A practical rule is about 207 N of usable work at 0.5 MPa, which vertically lifts roughly 18 kg with a 2:1 margin. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, S45C hard-chrome-plated 12 mm rod through both covers, fixed TPU bumpers at each end, a female M8x1.25 rod thread and 1/8" ports. Mounting options include FA/FB flange, LB foot and FTC brackets. Position sensing requires the optional -S magnet ordered with the cylinder; only then can CMSE or DMSE switches be slid into the body slots. Without -S there is no magnet fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED32X90
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.