Airtac ACED Double-acting Compact Cylinder ACED40X200SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED40X200SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø40mm bore and 200mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ40 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED40X200SB
A double acting, double-rod compact cylinder built to ISO 21287, the ACED40X200SB pushes a 40 mm bore through a 200 mm stroke with a rod leaving both covers. Because each side sees the rod-side area, output is equal in both directions: 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa. The male rod thread (B code) suits couplers and tooling that thread on directly, and the 1/8" port keeps plumbing simple.
The short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight guards and gantries. The S code means the magnet is fitted, so CMSE or DMSE switches can be clamped anywhere along the body for end-of-stroke detection. With 343 N usable at 0.5 MPa (about 60% of rating), it lifts roughly 29 kg vertically with a 2:1 margin. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the through-rod resists rotation while the rear rod can carry a sensor flag.
Airtac ACED Double-acting Compact Cylinder ACED40X200SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED40X200SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 200 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED40X200SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED40X200SB Is Used
Two-sided press fixture
The 200 mm stroke closes a jig from both covers at 571.8 N, letting one cylinder seat a part and eject it with equal force.
Bottle-line pusher gate
A rear rod on the through-rod carries a flag for DMSE switching, while the front rod swings a reject gate at 30-500 mm/s.
Pallet-stacking lift assist
With about 29 kg of vertical lift at a 2:1 margin, the 40 mm double rod guides a small stacker column symmetrically.
Is the Airtac ACED Double-acting Compact Cylinder ACED40X200SB the Right Cylinder?
Size both ways: the ACED32X50SB gives 345.6 N at 0.5 MPa for lighter clamping, while the ACED50X200SB steps up to 881.2 N for heavier tooling. At 200 mm this bore is at its maximum standard stroke, so no made-to-order length is needed. Remember the piston drifts if air is lost - add a rod lock or pilot check valve for held loads. FA/FB flanges, LB feet and FTC brackets bolt to the ISO 21287 face; I and Y knuckles suit the male rod thread. If you also need non-rotating precision, compare the TACED.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED40X200SB FAQ
Output is equal in both directions because a rod exits each cover: 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa, with a peak of 116.6 kgf at 1.0 MPa. Speed range is 30-500 mm/s on air filtered to 40 um, at 0.15-1.0 MPa (22-145 psi) operating pressure and 1.5 MPa (215 psi) proof pressure, from -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder. This S-coded unit carries the optional -S magnet, so CMSE or DMSE reed or solid-state switches clamp along the body slots. FA/FB flange, LB foot and FTC brackets mount on the standard face, and the fixed TPU bumpers at both ends absorb end-of-stroke impact.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED40X200SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.