Airtac ACED Double-acting Compact Cylinder ACED63X225
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X225 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 225mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke225 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X225
A double acting compact cylinder built to ISO 21287, the ACED63X225 pushes a 63 mm piston through a 225 mm stroke with a rod leaving BOTH covers, so thrust is identical on the extend and retract strokes: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa. The through-rod resists rotation and side load, and the rear rod can carry a sensor flag or a second tool. Operating range is 0.15-1.0 MPa (22-145 psi) with speed from 30 to 500 mm/s.
The hard-anodized aluminium body pairs with an S45C hard-chrome plated rod, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Because the short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, it slots into tight machine frames. At 0.5 MPa the rod-side force equals about 148 kgf, so halving for a 2:1 margin lets it lift roughly 74 kg vertically. Note: without the optional -S magnet no CMSE / DMSE switch can be fitted, and the cylinder does not hold position if air is lost.
Airtac ACED Double-acting Compact Cylinder ACED63X225 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X225 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X225
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X225 Is Used
Reciprocating conveyor pushers
The equal 1458.1 N force on both strokes keeps indexing and reject pushers on packaging lines consistent regardless of travel direction over the 225 mm span.
Counterbalanced lift columns
With about 74 kg of vertical lift at a 2:1 margin, the through-rod suits symmetric lift posts on gantry and assembly fixtures where a rear rod adds guidance.
Dual-end clamp fixtures
Machining jigs use the front rod to clamp and the back rod to drive a position flag, all inside a body about 50% shorter than an ISO 15552 profile cylinder.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X225 the Right Cylinder?
At 63 mm bore this model delivers 1458.1 N at 0.5 MPa in BOTH directions; if your load needs less, the ACED50X225 gives 881.2 N, while the ACED80X225 raises thrust to 2356.2 N. The 225 mm stroke sits inside the 250 mm standard limit for bore 63, so no made-to-order build is required. Choose the -S code if you want CMSE / DMSE switch positions, and pair FA/FB flange or LB foot brackets with the ISO 21287 mounting face. For a load that must stay put on air loss, add a rod lock or pilot check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X225 FAQ
Because a rod exits both covers, output is equal both ways: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa on every stroke, with a maximum of 297.4 kgf at 1.0 MPa. Working pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 225 mm stroke is within the 250 mm standard limit for bore 63.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, S45C hard-chrome rod, threaded covers and a fixed TPU bumper at each end. Position sensing requires the optional -S magnet code; only then can CMSE / DMSE switches be mounted on the body slots. Mounting brackets such as FA flange or LB foot bolt to the standard ISO 21287 face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X225
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.