Airtac ACED Double-acting Compact Cylinder ACED63X225SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X225SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 225mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke225 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X225SB
The ACED63X225SB is a double acting, double-rod ISO 21287 compact cylinder: a 16 mm rod exits both covers, so thrust is identical on every stroke because both sides work on the rod-side area. At 0.5 MPa it delivers 1458.1 N in either direction, rising to 2041.3 N at 0.7 MPa, with a peak of 297.4 kgf at 1.0 MPa. The male rod thread (B code) suits external nuts and clevises, and the fitted -S magnet lets CMSE / DMSE switches report piston position.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so a 225 mm stroke fits gantries and guarding where a full-length body will not. The through-rod resists rotation and side load and gives a symmetric mount, and the rear rod can carry a sensor flag. In practice, plan on roughly 875 N (about 89 kgf) of usable push at 0.5 MPa, which is a vertical lift of around 74 kg with a 2:1 margin. Fixed TPU bumpers absorb end-of-stroke shock at both covers, and the hard-anodized aluminium body with S45C hard-chrome rod runs 30-500 mm/s on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi).
Airtac ACED Double-acting Compact Cylinder ACED63X225SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X225SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X225SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X225SB Is Used
Reciprocating pallet pusher
The equal 1458.1 N thrust in both directions gives identical push and return force on a pallet transfer slide, so cycle timing stays the same loaded or empty.
Clamp-and-flip welding fixture
A rod at each cover lets one cylinder clamp a bracket on the front rod while the rear rod carries a position flag for the PLC, all inside a body about 50% shorter than an ISO 15552 profile cylinder.
Battery-change lift assist
With about 74 kg of vertical lift at a 2:1 margin, the through-rod guides a forklift battery roller deck symmetrically without a separate guide column.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X225SB the Right Cylinder?
Step down to an ACED50 (881.2 N at 0.5 MPa) when the load is lighter, or step up to an ACED80 (2356.2 N) for heavier tooling; the 63 mm bore sits in the middle with 1458.1 N both ways. At 225 mm the stroke is within the 250 mm standard range for this bore, so no made-to-order length is needed. FA/FB flange, LB foot and FTC brackets plus I/Y rod knuckles bolt to the ISO 21287 face. Remember that a plain double-rod cylinder drifts when air is lost - add a rod lock or pilot check if the load must stay put.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X225SB FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so output is equal either way: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, peaking at 297.4 kgf at 1.0 MPa. The 16 mm rod exits both covers, the port is 1/8" PT, and the male rod thread (B code) takes external nuts. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, freeing space in tight gantries and guards. This model carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches mount directly in the body slots for end-of-stroke or mid-stroke signals. Fixed TPU bumpers at both covers absorb end-of-stroke energy, and FA/FB flange, LB foot or FTC mounting bolts straight to the standard face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X225SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.