Airtac ACED Double-acting Compact Cylinder ACED63X35SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X35SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke35 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X35SB
A double acting compact cylinder built to ISO 21287, the ACED63X35SB pushes a 63 mm bore through a 35 mm stroke with a rod leaving both covers. Because each side works on the rod-side area, output is 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa in either direction - no push/pull imbalance to design around. The male rod thread (B code) and PT ports suit direct linkage to clamps and tooling.
The through-rod resists rotation and carries side load, and the rear rod can drive a sensor flag or a second tool. In practice, plan on roughly 875 N of usable work at 0.5 MPa, which is about 74 kg held vertically with a 2:1 margin - enough for lifting die carts or indexing a pallet fixture. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries, and the fitted -S magnet lets CMSE / DMSE switches report position. A fixed TPU bumper at each end absorbs end-of-stroke shock.
Airtac ACED Double-acting Compact Cylinder ACED63X35SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X35SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X35SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X35SB Is Used
Pallet indexing fixture
The symmetric through-rod pushes and retracts a pallet shuttle with equal 1458.1 N force, and the -S magnet signals home and extended to the PLC.
Small die cart lift
With about 74 kg of vertical lift at a 2:1 margin, the 63 mm double rod raises and lowers a die cart or jig table in a machine shop cell.
Benchtop press station
A rear rod carries a force-feedback flag while the front rod presses bushings into housings at 2041.3 N at 0.7 MPa, all inside a compact guard.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X35SB the Right Cylinder?
At 1458.1 N @0.5 MPa this bore sits between the 50 mm (881.2 N) and 80 mm (2356.2 N) double-rod sizes - step down for lighter clamping, up for heavy press-fit work. The 35 mm stroke is well inside the 250 mm standard range for bore 63, so no made-to-order build is needed. Remember the piston drifts if air is lost; add a rod lock or pilot check valve where a load must stay put. FA/FB flange, LB foot and FTC brackets bolt to the ISO 21287 face, and I/Y rod knuckles suit the male thread.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X35SB FAQ
As a double-rod cylinder, force is identical both ways: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a peak of 297.4 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/8" port serves the 63 mm bore.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so the 35 mm stroke fits shallow guards and gantry frames. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches can be clipped onto the body slots for end-of-stroke or mid-stroke sensing. A fixed TPU bumper at each end absorbs end-of-stroke energy.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X35SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.