Airtac ACED Double-acting Compact Cylinder ACED63X45SB
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X45SB is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 45mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke45 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X45SB
A double acting compact cylinder built to ISO 21287, the ACED63X45SB pushes a 63 mm bore through a 45 mm stroke with a piston rod leaving BOTH covers. Because each side sees the rod-side area, output is identical in either direction: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a peak of 297.4 kgf at 1.0 MPa. The male rod thread (B code) bolts straight to external tooling, and the fitted -S magnet accepts CMSE / DMSE switches for end-position sensing.
The hard-anodized aluminium body with an S45C hard-chrome rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s, with fixed TPU bumpers at both ends. Its short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight fixtures. As a rule of thumb, plan on roughly 875 N of usable work at 0.5 MPa, which lifts about 89 kg vertically - or about 74 kg with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED63X45SB Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X45SB |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 45 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X45SB
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X45SB Is Used
Reciprocating transfer carriage
The through-rod drives a pallet shuttle from either cover with equal 1458.1 N thrust, and the rear rod carries a position flag past a DMSE switch.
Clamp-and-support fixture
Male rod thread grips a swing clamp arm while the back rod steadies the jig; the 45 mm stroke suits short clamp-and-release cycles on a machining line.
Counterweight balancer arm
Symmetric rods on both ends balance a pivoting assembly on a packaging machine, with about 74 kg of vertical lift capacity at a 2:1 margin.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X45SB the Right Cylinder?
At 1458.1 N per direction, this bore sits between the 50 mm frame (881.2 N at 0.5 MPa) and the 80 mm frame (2356.2 N at 0.5 MPa), so pick down when the load is light and up when it is not. The 45 mm stroke is well inside the 250 mm maximum standard stroke for bore 63, so it ships as a catalogue item. Remember that a plain double-rod cylinder drifts when air is lost - add a rod lock or pilot check if the load must stay put. FA/FB flange, LB foot and FTC brackets plus I/Y rod knuckles mount on the ISO 21287 face, and the fitted -S magnet lets CMSE / DMSE switches clip onto the body slots.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X45SB FAQ
Force is equal both ways because a rod exits both covers and both strokes use the rod-side area: 1458.1 N at 0.5 MPa, 2041.3 N at 0.7 MPa, and a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FA/FB flange, LB foot or FTC brackets bolt to the standard face. The S code means the magnet is fitted, so CMSE / DMSE reed or solid-state switches mount in the body slots. A fixed TPU bumper at each end absorbs end-of-stroke energy but does not hold a load - use a rod lock or pilot check for that.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X45SB
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.