Airtac ACED Double-acting Compact Cylinder ACED63X55
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED63X55 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø63mm bore and 55mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke55 mm
- Port size1/8"
- Acting typeDouble acting, double rod
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED63X55
The ACED63X55 is a double acting, double-rod ISO 21287 compact cylinder: a 16 mm piston rod exits BOTH covers of the 63 mm bore body, so output force is equal in both directions - 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa on either stroke, because both sides work on the rod-side area. The through-rod resists rotation and side load and gives a symmetric mount, and the back-end rod can carry a sensor flag. Speed range is 30-500 mm/s with a fixed TPU bumper at each end.
The hard-anodized aluminium body with S45C hard-chrome-plated rod runs on 0.15-1.0 MPa (22-145 psi) filtered air, proof pressure 1.5 MPa (215 psi), temperature -20 to +70 C. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits tight jigs and gantries. In practice, plan for roughly 875 N of real work at 0.5 MPa (about 0.6 of the rating), which lifts about 74 kg vertically with a 2:1 margin. The optional -S magnet enables CMSE / DMSE switches; without -S there is no magnet.
Airtac ACED Double-acting Compact Cylinder ACED63X55 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED63X55 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 55 mm |
| Acting type | Double acting, double rod |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED63X55
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 63 | Bore size in mm. |
| ×55 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED63X55 Is Used
Benchtop crimping press
A 63 mm double-rod cylinder pushing 1458.1 N at 0.5 MPa from either side suits a small terminal-crimping fixture where the 55 mm stroke closes the dies and the back rod returns a stripper plate.
Bottling line pusher
On a beverage conveyor, the through-rod keeps the pusher bar square under side load while the equal 2041.3 N at 0.7 MPa diverts six-packs into lanes at up to 500 mm/s.
Gantry pick-and-place flag
In a CNC tending gantry, the rear rod of the ACED63X55 carries a flag for a DMSE switch (with the optional -S magnet) to confirm part clamping inside the short 55 mm envelope.
Is the Airtac ACED Double-acting Compact Cylinder ACED63X55 the Right Cylinder?
At 63 mm bore you sit between the 50 mm (881.2 N at 0.5 MPa) and 80 mm (2356.2 N at 0.5 MPa) double-rod sizes, so pick the ACED63X55 when your press or clamp needs near-1500 N both ways in a 55 mm stroke. Remember the piston drifts if air is lost - for a held load add a rod lock or pilot check. Bolt FA/FB flanges, LB feet or FTC brackets to the ISO 21287 face, and order the -S code if you want CMSE / DMSE position switches. Female M10x1.5 rod thread, PT ports, 1/8".
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED63X55 FAQ
Because a rod exits both covers, force is equal both ways: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa per direction (rod-side area). Maximum force at 1.0 MPa is 297.4 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end and FA/FB, LB or FTC mounting on the standard face. Position sensing needs the optional -S magnet ordered with the cylinder; only then can CMSE / DMSE switches be mounted on the body slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED63X55
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.