Airtac ACED Double-acting Compact Cylinder ACED80X225S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED80X225S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø80mm bore and 225mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke225 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED80X225S
A double acting compact cylinder built to ISO 21287, the ACED80X225S pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers the same 2356.2 N at 0.5 MPa (3298.7 N at 0.7 MPa) on every stroke - no push/pull imbalance to design around. The through-rod also resists rotation and carries side load better than a single-rod body, and the free back-end rod is a handy place to bolt a sensor flag. With 225 mm of travel it stays inside the 300 mm standard stroke range for this bore.
The hard-anodized aluminium body with an S45C hard-chrome-plated rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s, with a fixed TPU bumper at each end. Because the short ISO 21287 body saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, it slots into long-stroke gantries and guarded machines where a full-length body will not fit. This -S version carries the optional magnet, so CMSE / DMSE switches can be clipped on for end-of-stroke or mid-stroke detection. As a planning figure, treat about 1414 N (roughly 144 kgf) as the usable force at 0.5 MPa, which lifts about 72 kg vertically with a 2:1 margin.
Airtac ACED Double-acting Compact Cylinder ACED80X225S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED80X225S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 225 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED80X225S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 80 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED80X225S Is Used
Pallet stacker lift column
The symmetric through-rod guides a lift plate on a palletizing station; with about 72 kg of vertical lift capacity at a 2:1 margin, it handles loaded carton trays on a 225 mm lift.
Push-pull transfer unit
A rod at each end lets one cylinder clamp a workpiece on the forward side while the rear rod trips a limit flag - equal 2356.2 N force both ways at 0.5 MPa keeps the cycle symmetric.
Gantry press for assembly fixtures
The short ISO 21287 body fits inside a guarded gantry frame where an ISO 15552 profile cylinder would overhang, delivering 3298.7 N at 0.7 MPa for pressing bearings into housings.
Is the Airtac ACED Double-acting Compact Cylinder ACED80X225S the Right Cylinder?
At 2356.2 N per side at 0.5 MPa, this bore sits well above the 50 mm class (881.2 N) and below the 100 mm class (3769.9 N), so pick it when a 50 mm unit is under-rated but a 100 mm body is too bulky. Remember that a plain double-rod cylinder drifts when air is lost - add a rod lock or pilot check if the 225 mm stroke must hold a position. Mounting brackets (FA/FB flange, LB foot, FTC) plus I/Y rod knuckles bolt straight to the ISO 21287 face, and the fitted -S magnet means CMSE / DMSE switches work out of the box.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED80X225S FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so output is equal each way: 2356.2 N at 0.5 MPa, 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
The S means this unit carries the optional magnet, so CMSE or DMSE reed and solid-state switches can be mounted directly on the body slots for position sensing. Mechanically it is an ISO 21287 compact cylinder: hard-anodized aluminium body, S45C hard-chrome-plated 20 mm rod out of both covers, fixed TPU bumpers at both ends, and a body about 50% shorter in mounting length than an ISO 15552 profile cylinder. FA/FB flange, LB foot and FTC brackets plus I/Y knuckles bolt straight on; the rod end thread is female M12x1.75 and the port is 1/4" PT.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED80X225S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.