Airtac ACED Double-acting Compact Cylinder ACED80X45
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED80X45 is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø80mm bore and 45mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke45 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED80X45
A double acting compact cylinder built to ISO 21287, the ACED80X45 pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa in either direction - both strokes work on the rod-side area. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight press fixtures and guarded stations where a full-length body will not fit.
The through-rod resists rotation and side load and gives a symmetric mount, and the back-end rod can carry a sensor flag on a reciprocating table. A fixed TPU bumper at each end absorbs end-of-stroke energy, the hard-anodized aluminium body carries 1/4" ports, and the S45C hard-chrome rod runs at 30-500 mm/s. Plan on roughly 1414 N (about 144 kg) of real work at 0.5 MPa rather than the full rating, or about 120 kg lifted vertically with a 2:1 margin. Position is not held when air is lost - add a rod lock or pilot check for a held load.
Airtac ACED Double-acting Compact Cylinder ACED80X45 Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED80X45 |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 45 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED80X45
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 80 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED80X45 Is Used
Press fixture clamping
The 2356.2 N both-ways force clamps steel housings in a machining jig, and the 45 mm stroke clears part loading in seconds.
Reciprocating transfer slide
A rod on each cover balances the slide and resists rotation, moving pallets 45 mm between two stations at up to 500 mm/s.
Packaging pusher gate
The back rod drives a divert flag while the front rod pushes cartons off a conveyor lane, one cylinder doing both jobs.
Is the Airtac ACED Double-acting Compact Cylinder ACED80X45 the Right Cylinder?
At 2356.2 N per direction this bore sits between the 63 mm (1458.1 N) and 100 mm (3769.9 N) frames - step down if your load is under 900 N of working force, step up for heavy clamping over 1500 N. The 45 mm stroke is well inside the 300 mm standard range for bore 80. FA/FB flange, LB foot and FTC brackets plus I/Y rod knuckles bolt to the ISO 21287 face; the female M12x1.75 rod thread takes standard rod accessories. If you need CMSE or DMSE switches, order the -S code - without it no magnet is fitted and no sensor can be mounted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED80X45 FAQ
Because a rod exits both covers, force is equal in both directions: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, temperature -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end and FA/FB, LB or FTC mounting on the standard face. Sensing requires the optional -S magnet at order time; only then can CMSE or DMSE switches be clipped to the body.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED80X45
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.