Airtac ACED Double-acting Compact Cylinder ACED80X60S
The AirTAC Airtac ACED Double-acting Compact Cylinder ACED80X60S is a genuine double acting, double rod ISO 21287 compact air cylinder with a Ø80mm bore and 60mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ80 mm
- Stroke60 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACED Double-acting Compact Cylinder ACED80X60S
A double acting, double-rod ISO 21287 compact cylinder, the ACED80X60S pushes a 20 mm rod out of both covers, so the 80 mm bore delivers an identical 2356.2 N at 0.5 MPa (3298.7 N at 0.7 MPa) on every stroke - no push/pull imbalance to design around. The through-rod resists rotation and side load, and the rear rod end doubles as a carrier for a sensor flag or a symmetric second mount.
The hard-anodized aluminium body with an S45C hard-chrome-plated rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, with a fixed TPU bumper at each end. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this bore class fits cramped press fixtures and gantry clamps. Practical sizing: keep real work near 1414 N (about 0.6 of the rating), and the rod lifts roughly 120 kg vertically with a 2:1 margin. This -S model carries the optional magnet, so CMSE / DMSE switches mount directly on the body slots.
Airtac ACED Double-acting Compact Cylinder ACED80X60S Technical Specifications
| Model | Airtac ACED Double-acting Compact Cylinder ACED80X60S |
|---|---|
| Series | ACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACED Double-acting Compact Cylinder ACED80X60S
| ACED | ISO 21287 compact cylinder (double-rod). |
|---|---|
| 80 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACED Double-acting Compact Cylinder ACED80X60S Is Used
Press-side part ejection
The 2356.2 N symmetric thrust ejects stamped brackets off a die on both strokes, while the 60 mm stroke clears the tool in tight press frames.
Twin-sided gantry clamp
Rods on both covers clamp a machined housing from two sides with equal 3298.7 N force at 0.7 MPa, keeping the fixture symmetric.
Indexing with position feedback
The fitted -S magnet lets CMSE or DMSE switches report end-of-stroke on an automated pallet indexer running at 30-500 mm/s.
Is the Airtac ACED Double-acting Compact Cylinder ACED80X60S the Right Cylinder?
At 2356.2 N per direction, bore 80 sits between bore 63 (1458.1 N at 0.5 MPa) and bore 100 (3769.9 N at 0.5 MPa) - step down when the load is under 1400 N, step up for heavy clamp plates. The 60 mm stroke is well inside the 300 mm standard range for this bore. Remember the piston drifts if air is lost; add a rod lock or pilot check where a held load matters. FA/FB flanges, LB feet and FTC brackets bolt to the ISO 21287 face, and the female M12x1.75 rod thread takes standard I/Y knuckles.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACED Double-acting Compact Cylinder ACED80X60S FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so force is equal either way: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a peak of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um, -20 to +70 C.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so an 80 mm bore fits where a full-length body will not. A fixed TPU bumper at each end absorbs end-of-stroke impact, and because this model carries the optional -S magnet, CMSE / DMSE reed or solid-state switches click into the body slots for position sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACED Double-acting Compact Cylinder ACED80X60S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.