Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S
The AirTAC Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S is a genuine double acting, adjustable stroke ISO 21287 compact air cylinder with a Ø63mm bore and 60mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
- BoreØ63 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S
The ACEJ63X60-10S is a double acting AirTAC compact cylinder built to ISO 21287, with a 63 mm bore and a 60 mm stroke that an external stop screw trims down by up to 10 mm, giving a usable extend range of 50-60 mm on site. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N, rising to 2182.1 N at 0.7 MPa. The hard-anodized aluminium body carries a roller-burnished bore, and the S45C piston rod is hard-chrome plated for long seal life.
Because the short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, it slots into tight jigs, guarding and gantry frames where a full-length body will not fit. This -S version carries the optional magnet, so CMSE or DMSE reed and solid-state switches can be clamped anywhere along the body for end-of-stroke signalling. A fixed TPU bumper at each end absorbs end-of-stroke energy, and the female M10x1.5 rod thread drops straight into standard knuckles. As a planning figure, expect roughly 935 N of real work at 0.5 MPa, which lifts about 79 kg vertically with a 2:1 margin.
Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S Technical Specifications
| Model | Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 60 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 250 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 63 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S Is Used
Clamping fixtures on CNC pallets
With 1558.6 N push at 0.5 MPa and a 50-60 mm trim range, this cylinder clamps aluminium die-cast housings on machining pallets where the short ISO 21287 body fits inside the fixture envelope.
Packaging line pushers
The 60 mm stroke trimmed to 50 mm positions cartons precisely on a conveyor transfer, and the fitted magnet with a DMSE switch confirms each push without an external sensor bracket.
Assembly press assist
Pressing bearings into small pump housings needs about 935 N of usable force at 0.5 MPa; the TPU bumpers absorb the impact at each end of the short stroke cycle.
Is the Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S the Right Cylinder?
Size this bore when your load sits between the 40 mm class (628.3 N push at 0.5 MPa) and the 80 mm class (2513.3 N push at 0.5 MPa); the 63 mm delivers 1558.6 N push and 1458.1 N pull at 0.5 MPa. If you only need to trim the extend stroke by a few millimetres for part tolerance, the 10 mm window here is enough - order a wider -20 to -100 code if the stroke must vary more. Remember the stop screw is a mechanical end stop only: on air loss the piston drifts, so add a valve or external lock if you must hold position. FA flange, LB foot, FTC brackets and I/Y rod knuckles bolt to the ISO 21287 face, and the fitted magnet works with CMSE / DMSE switches.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa it pushes 2182.1 N and pulls 2041.3 N; the theoretical maximum is 317.9 kgf at 1.0 MPa. The -10 code is a 10 mm adjustment window: an external stop screw shortens the 60 mm extend stroke by up to 10 mm, so the working range is 50-60 mm. It cannot lengthen the stroke past 60 mm, and it is an end stop only - it does not hold a load if air is lost. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it suits tight guarding and fixture frames. The rod end has a female M10x1.5 thread and the air port is 1/8" PT. This -S model carries the optional magnet, so CMSE or DMSE reed and solid-state switches mount in the body slots for position feedback; without the S code there would be no magnet. FA flange, LB foot and FTC brackets plus I/Y knuckles bolt straight to the standard face.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac ACEJ50~63 Adjustable Compact Air Cylinder ACEJ63X60-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.