
The AirTAC Adjustable Cylinder SAIJ32 SAIJ32AX165-30 is a genuine double-acting ISO 15552 profile-barrel air cylinder with a Ø32mm bore and 165mm stroke, G1/8 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SAIJ32X165-30 is a double-acting ISO 15552 profile cylinder featuring a rear-mounted stroke adjuster. It provides a 135-165 mm usable travel window, allowing you to dial back the 165 mm nominal stroke by up to 30 mm during commissioning.
This model features a SUS420J2 stainless steel rod (material code A) for enhanced corrosion resistance compared to standard carbon steel. The extruded aluminum barrel includes sensor grooves on both sides, though this specific SKU omits the magnet, meaning external position sensing is not supported without modification. The rear adjuster acts purely as a mechanical stop to set the end position and does not hold the load without continuous air pressure.
| Model | Airtac Adjustable Cylinder SAIJ32 SAIJ32AX165-30 |
|---|---|
| Series | SAI ISO 15552 profile cylinder |
| Bore size | Ø32 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | G1/8 |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 27 mm |
| Max stroke | Up to 1000 mm |
Specifications follow the official AirTAC SAI series datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Port options: G (BSPP) / NPT.
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 346 N | 346 N |
| 0.7 MPa | 484 N | — |
| Max (@1.0 MPa) | 70 kgf | |
Double-rod model: the rod passes through the rear cover, so both piston faces lose rod area and push is shown at the annular-area value. Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SAI | ISO 15552 profile-barrel cylinder series. |
|---|---|
| 32 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for sensor position sensing. |
Related SAI-family variants: SAID (double rod), SAIJ (adjustable stroke), SAIL (with lock), SAIF (with valve), BSAI (enclasp / clamp-lock), and SAI-S with built-in magnet. Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B); seals: TPU (blank) / Viton H / NBR N.
Quickly adjust the 135-165 mm travel window to accommodate different product sizes on the same line without changing the cylinder.
Fine-tune the retract stroke by up to 30 mm during initial setup to achieve exact positioning without external stopper hardware.
The adjustable stroke is ideal for fine-tuning machinery without swapping cylinders or adding external stops.
For an exact ISO 15552 replacement, match the 32 mm bore, 165 mm stroke, 30 mm adjustment range, PT port thread, and SUS420J2 rod material. Because this model lacks a magnet (-S), it cannot use AirTAC CMSE or DMSE sensors. Remember that the rear adjuster is a travel stop, not a lock; for load-holding without live air, consider the SAIL or BSAI series. Since the stroke is under 300 mm, side-load stress on the 12 mm rod is moderate, but external guiding is still recommended for heavy lateral loads.
AirtacDistr lists every SAIJ32-SUS order code with its price on one page at https://airtacdistr.com/products/airtac-saij32-sus-adjustable-cylinder
Quick checklist
At the maximum 1.0 MPa pressure, it can deliver up to 82 kgf.
The rear adjuster screw allows you to mechanically shorten the effective stroke from 165 mm down to as little as 135 mm. This creates a 135-165 mm usable travel window for fine-tuning the end position without swapping the cylinder.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.