
The AirTAC GAFR Adjustable Filter Regulator GAFR20008ALWT is a genuine two-in-one filter & regulator — a diversion-type water/particulate filter and a balanced pressure regulator built into ONE body. It has 1/4" ports, a 5 µm filter element and regulates 0.15 - 0.4 MPa (20 - 58 psi). It has no lubricator, so it adds no oil to the airflow.
The GAFR20008ALWT is a filter and regulator combined into a single body, removing the need for separate GAF and GAR units. It cleans incoming air through a diversion structure that spins out liquid water and solid particles, then delivers a steady outlet pressure via a balanced, self-locking regulator knob.
This model uses a 1/4in port, a lower-pressure range of 0.15-0.4 MPa (20-58 psi), and a 5 um element for finer filtration. The automatic drain clears the 25 cc condensate bowl without manual attention, and the included circular gauge shows the set pressure on an MPa/psi scale. This version has NPT ports (the T in the order code) for North American pipe fittings.
| Model | Airtac GAFR Adjustable Filter Regulator GAFR20008ALWT |
|---|---|
| Series | GAFR200 filter & regulator |
| Port size | 1/4" (NPT thread) |
| Filtering grade | 5 µm |
| Pressure range | 0.15 - 0.4 MPa (20 - 58 psi) |
| Type | Lower pressure |
| Bowl material | PC |
| Drain type | Automatic drain |
| Fluid | Air |
|---|---|
| Max. pressure | 1.0 MPa (145 psi) |
| Proof pressure | 1.5 MPa (215 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Capacity of drain bowl | 25 cc |
| Bracket | Included |
| Weight | 290 g |
Specifications follow the official AirTAC GAFR catalogue (pages 235-236). Air must not freeze in the unit. The fitted circular gauge reads in psi / bar, set by the NPT thread code. This unit filters and regulates only; it does not add lubrication.
| GAFR200 | GA200 series filter & regulator — sets the port range, drain-bowl capacity and weight. |
|---|---|
| (blank) | Bowl material: PC. Available on this body: PC (blank), Metal (C), Nylon (N). |
| 08 | Port size 1/4". This body offers 06 = 1/8", 08 = 1/4". |
| A | Drain: Automatic drain. |
| L | Lower pressure type — 0.15 - 0.4 MPa (20 - 58 psi). This body offers Standard (S) or Lower pressure (L). |
| (blank) | Mounting bracket included. |
| (blank) | Circular pressure gauge fitted. |
| W | Filtering grade 5 µm. |
| T | NPT thread; gauge scale psi / bar. |
| (blank) | No reverse-flow valve. |
The filter and the regulator are ONE body here — there is no separate GAF filter or GAR regulator part to assemble. Need lubrication downstream too? Add a lubricator by ordering the matching GAFC200-08 F.R.L. combination instead.
Figures are the end of the flow curve plotted in the AirTAC catalogue at 0.7 MPa inlet pressure — a sizing envelope for comparing bodies, not a rated flow. Read the catalogue curve for a real duty point. Outlet pressure falls as flow rises, so size a body with headroom above your peak demand.
| This model | GAFR200 · 1/4" · curve to 2000 L/min |
|---|---|
| One size up | GAFR300 (curve to 3500 L/min) |
| Add a lubricator | GAFC200-08 (F.R.L. combination) |
Feed a single pneumatic valve or small actuator with the 5 um element to protect fine internal clearances from particle wear.
Mount on a test bench to supply a regulated 0.15-0.4 MPa air supply for low-pressure experiments or calibration checks.
Install on a small assembly station where the 290 g weight and 1/4in port fit tight spaces without overloading the structure.
Choose the GAFR200 body for small jigs or single actuators where a 1/4in port and 290 g weight suit compact layouts. The 5 um element traps finer particles than the standard 40 um, making it suitable for precision valves, though it will need more frequent service. The automatic drain handles wet or unattended lines, while the included bracket simplifies panel mounting. The lower-pressure type tops out at 0.4 MPa, so confirm your system never needs more than that. If oil is required downstream, order the matching GAFC200-08 combination instead. 1.0 MPa max supply leaves about 0.6 MPa above the 0.4 MPa top of the range.
Quick checklist
This is a filter and regulator only — it delivers filtered, pressure-set air with no added oil. If a downstream tool needs lubrication, add a separate lubricator or order the GAFC200-08 combination; do not expect an oil mist from this unit.
The pressure range is 0.15-0.4 MPa (20-58 psi), with a 1.0 MPa (145 psi) maximum and 1.5 MPa (215 psi) proof pressure. Operating temperature is -5 to 70 C. The drain bowl holds 25 cc and the unit weighs 290 g.
The W code specifies a 5 um element that traps much finer solid particles, which is beneficial for precision valves or instrument air. The trade-off is that the finer element will clog faster and require more frequent replacement than a 40 um element.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7 hours.