
The AirTAC GC300-10 FRL Unit (GC30010ALF1WTK) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT3/8" ports, a 5 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
GC30010ALF1WTK is a genuine AirTAC G-series three-unit F.R.L. combination: separate filter, regulator and lubricator units that together clean, regulate and oil-mist lubricate a compressed-air line. This 300-size set is ported 3/8 inch with a NPT thread, carries the 5 um (W) filter element with an automatic drain on the filter bowl, and is built on the low-pressure (L) type regulator with the embedded square gauge scaled in MPa. The K suffix fits a reverse (check) valve in the regulator section. At size 300 the filter and lubricator bowls are polycarbonate (PC).
AirTAC builds the G series in sizes 200, 300, 400 and 600, with differential-pressure, automatic or manual drains, 40 um or 5 um filtration, three thread types (NPT on this code), gauge styles and scales, a low-pressure regulator option and an optional reverse valve. Maximum working pressure is 1.0 MPa (145 psi) and the temperature range is -5 to 70 C, non-freezing. Flow is published as curves rather than a single rating, so we confirm the datasheet and flow figures for this set on request.
| Model | AirTAC GC300-10 FRL Unit (GC30010ALF1WTK) |
|---|---|
| Series | GC300 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT3/8" (NPT thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | PC |
| Pressure gauge | Fitted — square, MPa scale |
| Reflux valve | Fitted (reverse flow permitted) |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC300 | G-series F.R.L. combination, 300 body — sets the port range. |
|---|---|
| 10 | Port size PT3/8". This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| (blank) | Pressure gauge fitted (blank). |
| F | Gauge shape: Square. C is round, F is square. |
| 1 | Gauge scale: MPa. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| K | Reverse-flow (reflux) valve fitted. |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF300-10 filter, GR300-10 regulator and GL300-10 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC300 · PT3/8" · 5 µm |
|---|---|
| One size down | GC200 |
| One size up | GC400 |
| Two-unit equivalent | GFC300-10 |
| Build order | Filter → regulator → lubricator |
Supplying power clamps on a machining-centre fixture, where the fitted check valve helps hold the clamped circuit if the shop air supply dips mid-cycle.
Conditioning the air feeding a pneumatic dock leveller or lift-assist ram, with the check valve limiting back-flow when the upstream supply is shut down.
Holding position on the clamp and pusher circuits of a palletiser, where the check valve limits back-flow if upstream pressure is lost during a cycle.
Size 300 with a 3/8 inch NPT port is the mid step of the range; step to 200 for small drops or to 400/600 for larger mains and higher air demand. The W suffix selects the 5 um element, with the standard 40 um grade available for coarse protection, and the A suffix fits an automatic drain (manual and differential-pressure are alternatives). This is the low-pressure (L) type regulator; with the automatic drain the catalogue set range is 0.15-0.9 MPa (20-130 psi). The K suffix is the key choice here: it adds a reverse (check) valve so the downstream circuit is not vented back through the set if the supply dips - leave K out if you do not need that hold function. The embedded square gauge reads in MPa, with other scales and the round gauge orderable. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Flow is published only as curves, so ask us to confirm sizing before ordering.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR300-10 regulator with a GF300-10 filter on that branch.
AirTAC publishes G-series flow as curves against pressure rather than a single rated figure, so we do not quote one number here. Send us your working pressure and air demand and we will confirm the flow data for this 3/8 inch NPT set from the datasheet before you order.
K fits a reverse (check) valve in the regulator section. It blocks back-flow through the unit, helping hold downstream pressure if the upstream supply dips or is shut off - useful on clamping and holding circuits. If you do not need that function, order the same set without the K suffix.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.