
The AirTAC GC400-10 FRL Unit (GC40010ALNWT) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT3/8" ports, a 5 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
GC40010ALNWT is an AirTAC GC-series three-unit F.R.L. combination: separate filter, regulator and lubricator built as one 400-size set on NPT 3/8-inch ports. The W selects the finer 5 um filter element instead of the standard 40 um, so the air reaching the regulator and lubricator - and everything downstream - carries less particulate. This code also carries the automatic-drain filter bowl (A), the low-pressure regulator type (L) and no gauge (N). Both bowls are polycarbonate at size 400, the medium is compressed air only, maximum working pressure is 1.0 MPa (145 psi), and operating temperature is -5 to 70 C (non-freezing).
This is a genuine AirTAC part sold by a US distributor. The GC series is also available in 200, 300 and 600 sizes with ports from 1/8 to 1 inch, with manual or differential-pressure drains, gauge options, G/BSPP and NPT thread options and optional brackets. Flow is published as curves rather than a single rated figure, so ask us to confirm the datasheet and sizing for your application on request.
| Model | AirTAC GC400-10 FRL Unit (GC40010ALNWT) |
|---|---|
| Series | GC400 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT3/8" (NPT thread) |
| Filtering grade | 5 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Low-pressure type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | PC |
| Pressure gauge | Not fitted |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. The low-pressure type adjusts over a lower band than standard; we confirm the exact figures from the factory datasheet. The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC400 | G-series F.R.L. combination, 400 body — sets the port range. |
|---|---|
| 10 | Port size PT3/8". This body offers 10 = PT3/8", 15 = PT1/2". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| L | Low-pressure type. Blank is standard, L is the low-pressure type. |
| N | No pressure gauge (N). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| W | Filtering grade 5 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF400-10 filter, GR400-10 regulator and GL400-10 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC400 · PT3/8" · 5 µm |
|---|---|
| One size down | GC300 |
| One size up | GC600 |
| Two-unit equivalent | GFC400-10 |
| Build order | Filter → regulator → lubricator |
Supplies low-pressure air to clamps and agitators on a laboratory sample-preparation bench, where the 5 um element keeps particulate out of sensitive bench equipment.
Conditions the air feeding spray guns in a woodshop finishing booth, combining the finer 5 um filtration with oil mist for gun and regulator longevity.
Runs the gentle low-pressure clamps on an electronics assembly fixture bench, with filtered, regulated and lubricated air from a single 3/8-inch set.
The 400 size suits lines already built around 3/8-inch supply piping; step down to 300 for lighter duty or up to 600 for heavier circuits - we confirm the sizing from the published flow curves on request. This code gives you the automatic drain (A), which is the low-maintenance choice, while manual (M) and differential-pressure (blank) drains are orderable alternatives. The key choice here is filtration: W selects the 5 um element for cleaner supply air, versus the standard 40 um. The L selects the low-pressure regulator type - confirm its adjustment range with us - and N means no gauge, though gauge options can be added. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. brackets are optional.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR400-10 regulator with a GF400-10 filter on that branch.
AirTAC publishes flow for the GC series as curves across pressure ranges rather than a single rated figure, so quoting one number would not be accurate. Share your working pressure and consumption with us and we will confirm the flow and datasheet on request before you order.
The 40 um element is the standard choice for general actuator supply. The W in GC40010ALNWT selects the 5 um element for cleaner air to more sensitive downstream equipment. Both grades are catalogue options in the same body - keep the W in the code when you need the finer grade.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.