
The AirTAC GC400-10 FRL Unit (GC40010ANT) is a genuine G-series three-unit F.R.L. combination: a separate filter, a separate regulator and a separate lubricator assembled as one air-preparation station. It has PT3/8" ports, a 40 µm element, a automatic drain and regulates 0.15 - 0.9 MPa (20 - 130 psi).
GC40010ANT is an AirTAC GC-series three-unit F.R.L. combination: a separate air filter, pressure regulator and lubricator assembled as one 400-size set on NPT 3/8-inch ports. With the standard 40 um element it removes water and particulate, sets downstream working pressure, and meters oil mist to the cylinders and air tools that follow. This code carries the automatic-drain filter bowl (A), the standard regulator type and no gauge (N). The filter and lubricator bowls are polycarbonate at size 400. The regulator adjusts from 0.15 to 0.9 MPa (20-130 psi) on this automatic-drain version. The medium is compressed air only, maximum working pressure is 1.0 MPa (145 psi), and operating temperature is -5 to 70 C (non-freezing).
This is a genuine AirTAC part sold by a US distributor. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Flow is published as curves rather than a single rated figure, so ask us to confirm the datasheet and sizing on request.
| Model | AirTAC GC400-10 FRL Unit (GC40010ANT) |
|---|---|
| Series | GC400 F.R.L. combination |
| Composition | Filter + regulator + lubricator (3 units) |
| Port size | PT3/8" (NPT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Automatic drain |
| Bowl material | PC |
| Pressure gauge | Not fitted |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). The combination has no separate bracket code — the three units couple together with their own mounting hardware. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GC400 | G-series F.R.L. combination, 400 body — sets the port range. |
|---|---|
| 10 | Port size PT3/8". This body offers 10 = PT3/8", 15 = PT1/2". |
| A | Drain: Automatic drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| N | No pressure gauge (N). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| T | NPT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, gauge, shape, scale, grade, thread, reflux — there is no bracket position on a combination. Constituent units, orderable separately as spares: GF400-10 filter, GR400-10 regulator and GL400-10 lubricator.
A GC is three separate units, so the filter and the regulator can each be serviced or replaced on their own. A GFC is the two-unit set, where filtering and regulating share one body — shorter, but the two functions come as one part. Both filter, regulate and lubricate.
| This model | GC400 · PT3/8" · 40 µm |
|---|---|
| One size down | GC300 |
| One size up | GC600 |
| Two-unit equivalent | GFC400-10 |
| Build order | Filter → regulator → lubricator |
Feeds a small air press on a job-shop stamping bench with filtered, regulated, lubricated air, so the press cylinders run on conditioned supply from one 3/8-inch set.
Conditions the supply at a maintenance-shop tool drop where nailers and impact drivers are used all shift, with the lubricator oil-misting the tools and the automatic drain clearing the bowl.
Supplies the gripper manifolds on an assembly robot cell, where the standard regulator sets actuation pressure and the 40 um element keeps debris out of the gripper circuit.
Pick the 400 size where 3/8-inch supply piping is specified; drop to 300 for lighter circuits or step to 600 when the line grows - because flow appears only as curves, we confirm the fit against your consumption before ordering. The automatic drain (A) handles bowl emptying unattended; manual (M) and differential-pressure (blank) drains are alternatives. Element grade is the standard 40 um (order W for 5 um), and the regulator is the standard type adjusting 0.15-0.9 MPa (20-130 psi) on this automatic-drain set. N means no gauge is fitted, though gauge options can be selected in the code. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
Quick checklist
The PC bowls must not be cleaned with solvents — wipe them with a dry cloth. The lubricator adds an oil mist downstream of the regulator. If any branch of the line must stay oil-free, take that branch off before the lubricator, or use a GR400-10 regulator with a GF400-10 filter on that branch.
There is no single rated flow figure to quote: AirTAC publishes flow for the GC series as characteristic curves across pressure ranges. Tell us your working pressure and air consumption and we will confirm the flow and the full datasheet on request before you order.
The N in the code specifies the set without a pressure gauge; the regulator itself remains fully adjustable. If you want fitted pressure indication, gauge options for GC units can be selected in the code when ordering.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7 hours.