Airtac GF Filter GF200C06JW
The AirTAC Airtac GF Filter GF200C06JW is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 40 µm element, with See datasheet ports and a differential-pressure drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizeSee datasheet
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Inlet pressure0.15 - 1.0 MPa (22 - 145 psi)
- Bowl materialPC
- ThreadPT
- BracketMounting bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GF Filter GF200C06JW
The AirTAC GF200C06JW is a G-series air filter in the 200 size and a genuine AirTAC part for water and particulate removal only - no pressure regulation, no lubrication. The W code selects the 5 um fine filtration element in place of the standard 40 um grade, the choice for protecting precision downstream components, and the J code means no mounting bracket is supplied. Ports are PT1/8 in. (PT standard; G and NPT are orderable options), the drain is differential-pressure and clears condensate automatically, maximum working pressure is 1.0 MPa (145 psi), and the polycarbonate bowl suits the 200 size. Operating temperature is -5 to 70 C (non-freezing).
This is one configuration of the AirTAC G-series filter family, which spans sizes 200, 300, 400 and 600 with standard 40 um or optional 5 um elements and a choice of differential-pressure, automatic or manual drains. Because AirTAC publishes filter flow as curves rather than a single rated figure, we will confirm the datasheet and sizing details for your application on request.
Airtac GF Filter GF200C06JW Technical Specifications
| Model | Airtac GF Filter GF200C06JW |
|---|---|
| Series | GF200 air filter |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Drain type | Differential-pressure drain |
| Bracket | Mounting bracket included |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | PC |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac GF Filter GF200C06JW
| GF200 | G-series air filter, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain. Options are differential (blank), automatic (A) or manual (M). |
| (blank) | Mounting bracket included. A bracket ships by default; J orders it without. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF200 · See datasheet · 40 µm |
|---|---|
| One size up | GF300 |
| Line order | Filter first, then regulator, then lubricator |
Where the Airtac GF Filter GF200C06JW Is Used
Lab analyser sample-purge air
Fitted on the instrument-air feed to laboratory gas analysers or environmental cabinets, the 5 um element keeps fine particulate out of sensitive pneumatic metering and switching components. The differential-pressure drain handles condensate without scheduled attention.
Proportional valve skid protection
Installed immediately upstream of proportional directional valves on a motion-control skid, the fine element reduces particle contamination that degrades spool response. Inline mounting without a bracket suits compact hydraulic/pneumatic cabinets.
Detail paint-gun air drop
Used at a finishing-station drop feeding HVLP or detail spray guns, the filter removes water and fine debris that cause fisheyes and texture defects in the coating, while the automatic drain action keeps the bowl from passing moisture through.
Is the Airtac GF Filter GF200C06JW the Right Filter?
Pick the 5 um element over the standard 40 um grade when the air feeds precision pneumatic components - pilot valves, proportional valves, air bearings, measurement devices - where finer particulate must be removed; note that a finer element is best treated as a polishing stage downstream of general plant filtration. The PT1/8 in. ports and 200 size are the smallest G-series step; if demand is higher, step to 300/400/600 and let us confirm the flow curve against your consumption before ordering. Drain options are differential-pressure (this unit), automatic (A) or manual (M). Thread is PT as standard - specify G (BSPP) or NPT (T) at order if needed. J means no bracket; order the bracketed variant for wall mounting.
Quick checklist
- ✓ Body size for your peak flow (See datasheet here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0.15 - 1.0 MPa (22 - 145 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 40 µm element when pressure loss rises.
The PC bowl must not be cleaned with solvents or exposed to synthetic oils that attack polycarbonate — wipe it with a dry cloth. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
Airtac GF Filter GF200C06JW FAQ
AirTAC states filter performance as flow curves, not a single rated number, and the finer 5 um element affects the curve relative to the standard grade. We do not quote a figure here - share your pressure and consumption and we will confirm the sizing from the datasheet on request.
The standard 40 um grade suits general plant-air protection for cylinders and hand tools. Choose this W-coded unit when the air supplies precision components such as pilot-operated or proportional valves, or process equipment where fine particulate causes faults. Both grades are catalogue options in the same 200-size body.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC Air-Preparation Units
Request a Quote for Airtac GF Filter GF200C06JW
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.