Airtac GF Filter GF300C10AW
The AirTAC Airtac GF Filter GF300C10AW is a genuine G-series air filter. It separates condensed water and filters particulate from the compressed-air line through a 40 µm element, with See datasheet ports and a differential-pressure drain. A filter does not set downstream pressure — pair it with a GR regulator, or use a GFR filter regulator, when pressure control is needed.
- TypeAir filter
- Port sizeSee datasheet
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Inlet pressure0.15 - 1.0 MPa (22 - 145 psi)
- Bowl materialPC
- ThreadPT
- BracketMounting bracket included
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GF Filter GF300C10AW
GF300C10AW is an AirTAC GF-series air filter, a filtration-only unit: it removes condensed water and particulate from compressed air, with no pressure regulation and no lubrication. This configuration is the size 300 body with a 3/8" PT port, the fine 5 um filter element, an automatic drain that discharges condensate from the polycarbonate bowl on its own, and a mounting bracket included for fixing to the machine frame or a preparation plate. Maximum working pressure is 1.0 MPa (145 psi); temperature range is -5 to 70 C (non-freezing).
This is a genuine AirTAC part. The GF series spans sizes 200, 300, 400 and 600, with 40 um standard or 5 um (W) filtration, differential-pressure (default), automatic (A) or manual (M) draining, and optional G (BSPP) or NPT (T) threads in place of the standard PT. Flow performance is published as curves rather than one rated figure, so ask us to confirm the datasheet and flow data against your application on request.
Airtac GF Filter GF300C10AW Technical Specifications
| Model | Airtac GF Filter GF300C10AW |
|---|---|
| Series | GF300 air filter |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Drain type | Differential-pressure drain |
| Bracket | Mounting bracket included |
| Fluid | Compressed air |
|---|---|
| Inlet pressure | 0.15 - 1.0 MPa (22 - 145 psi) |
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Bowl material | PC |
| Feature | Low pressure loss |
Specifications follow the official AirTAC G-series air-preparation data. The inlet-pressure band is set by the drain type: automatic and differential-pressure drains run 0.15 - 1.0 MPa, a manual drain runs 0 - 0.9 MPa. Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac GF Filter GF300C10AW
| GF300 | G-series air filter, 300 body — sets the port range. |
|---|---|
| C1 | Port size See datasheet. This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| (blank) | Drain: Differential-pressure drain. Options are differential (blank), automatic (A) or manual (M). |
| (blank) | Mounting bracket included. A bracket ships by default; J orders it without. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
Field order is size, port, drain, bracket, grade, thread — a blank position takes the default. Example: GF300-10AJW is a 300 body, PT3/8", automatic drain, no bracket, 5 µm element, PT thread.
Size Class
- GF200PT1/8" - PT1/4"
- GF300PT1/4" - PT1/2"
- GF400PT3/8" - PT1/2"
- GF600PT3/4" - PT1"
A larger body carries a larger port and passes more air at the same pressure drop. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom rather than from a single rated figure. The GF600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GF300 · See datasheet · 40 µm |
|---|---|
| One size down | GF200 |
| One size up | GF400 |
| Line order | Filter first, then regulator, then lubricator |
Where the Airtac GF Filter GF300C10AW Is Used
Robot gripper air preparation
Bracket-mounted beside an industrial robot's valve stack, it filters the air feeding gripper and clamping actuators, with the 5 um element guarding fine pilot valves and automatic drain keeping moisture out during continuous cycles.
Food and beverage line actuators
Installed on the air drops serving filling and capping machine actuators, it removes water and fine particulate; the included bracket allows clean mounting on the line frame and the automatic drain suits areas with limited maintenance access.
Control panel air feed
Fixed by its bracket next to a machine's pneumatic control panel, it conditions the supply to directional valves and I/P components, keeping condensate and 5 um-scale particles away from sensitive pilot circuits.
Is the Airtac GF Filter GF300C10AW the Right Filter?
The size 300 body with 3/8" PT port is the middle step of the GF range; move to 400 or 600 where the branch serves heavier air demand, or to 200 for compact drops. The 5 um (W) element suits points of use feeding valves and cylinders that need finer protection than the standard 40 um, and the automatic drain (A) removes the need for routine manual draining. The bracket is included in this version for secure wall or frame mounting; the J suffix deletes it if you mount otherwise. PT is the standard thread, with G (BSPP) and NPT (T) available as catalogue options. Flow is published as curves, not a single rating, so ask us to confirm sizing from the datasheet before ordering.
Quick checklist
- ✓ Body size for your peak flow (See datasheet here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain: differential, automatic or manual
- ✓ Manual drain caps inlet at 0.9 MPa
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Bracket needed, or order with J
Installation & Maintenance Notes
- check Mount vertically, bowl down, and follow the airflow arrow.
- check Put the filter first in the air-preparation line.
- check Keep inlet pressure within 0.15 - 1.0 MPa (22 - 145 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
- check Replace the 40 µm element when pressure loss rises.
The PC bowl must not be cleaned with solvents or exposed to synthetic oils that attack polycarbonate — wipe it with a dry cloth. A filter removes water and particulate only; it does not regulate pressure or add lubrication.
Airtac GF Filter GF300C10AW FAQ
AirTAC states filter performance as flow curves rather than a single rated flow number, so no figure is quoted here. Send us your working pressure and required air consumption and we will confirm the datasheet flow data for this model on request before you commit.
Yes. GF300C10AW has no J suffix, so the mounting bracket is included for fixing the unit to a frame or preparation plate. If you prefer to mount by other means, the J version of the same filter is supplied without a bracket.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac GF Filter GF300C10AW
Send us the quantity, thread type (PT / G / NPT) and destination. We confirm price, availability and lead time — usually within 7-8 hours.