Airtac GFR Filter Regulator GFR300C10NW
The AirTAC Airtac GFR Filter Regulator GFR300C10NW is a genuine G-series filter regulator: water separation, 40 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has See datasheet ports, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
- TypeFilter regulator
- Port sizeSee datasheet
- Regulating range0.15 - 0.9 MPa (20 - 130 psi)
- Filtering grade40 µm
- DrainDifferential-pressure drain
- Bowl materialPC
- Pressure gaugeFitted
- ThreadPT
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac GFR Filter Regulator GFR300C10NW
This AirTAC GFR filter regulator cleans and regulates compressed air in one body: the bowl separates water and particles, which the drain removes, and the adjusting knob sets the downstream pressure. The W code fits the 5 um element for finer filtration than the 40 um standard. This configuration is the 300 size with a PT3/8 port, differential-pressure drain and no pressure gauge. Maximum inlet pressure is 1.0 MPa (145 psi); with the differential-pressure drain the regulator adjusts from 0.15 to 0.9 MPa (20-130 psi).
It is a genuine AirTAC part from the G series, which spans sizes 200 to 600 (1/8 in. to 1 in. ports) with 40 um or 5 um elements, differential-pressure, automatic or manual drains, and gauge or no-gauge variants. The 300 size carries a polycarbonate bowl and handles non-freezing compressed air from -5 to 70 C. Flow is published as curves rather than a single rated figure, so we confirm datasheet and flow figures on request.
Airtac GFR Filter Regulator GFR300C10NW Technical Specifications
| Model | Airtac GFR Filter Regulator GFR300C10NW |
|---|---|
| Series | GFR300 filter regulator |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
Model Code: Airtac GFR Filter Regulator GFR300C10NW
| GFR300 | G-series filter regulator, 300 body — sets the port range. |
|---|---|
| C1 | Port size See datasheet. This body offers 08 = PT1/4", 10 = PT3/8", 15 = PT1/2". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Mounting bracket included. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
Size Class
- GFR200PT1/8" - PT1/4"
- GFR300PT1/4" - PT1/2"
- GFR400PT3/8" - PT1/2"
- GFR600PT3/4" - PT1"
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR300 · See datasheet · 40 µm |
|---|---|
| One size down | GFR200 |
| One size up | GFR400 |
| Add lubrication | GFC300-C1 (two-unit set) |
Where the Airtac GFR Filter Regulator GFR300C10NW Is Used
Spray-gun atomizing air
Preparing regulated air for spray guns in a paint or coating booth; with no lubricator in this circuit, the unit adds no oil mist to the air reaching the finish.
Analyzer cabinet actuation
Supplying pneumatic actuators and purge air inside an analytical instrument cabinet, where the 5 um element helps keep fine internal passages clear.
Electronics assembly grippers
Feeding small gripper cylinders on an electronics assembly module, where finer filtration helps protect compact valve and cylinder internals.
Is the Airtac GFR Filter Regulator GFR300C10NW the Right Unit?
Pick the frame by port and air demand: the 300 carries a 3/8 in. PT port, between the 1/4 in. 200 and the 1/2 in. 400. The 5 um (W) element here suits duties where the standard 40 um grade is too coarse; both grades remain orderable in this frame. The differential-pressure drain (blank code) clears condensate using the working differential, with automatic (A) and manual (M) drains as alternatives. No gauge is fitted (N) and gauge variants are available; PT is the standard thread with G (BSPP) and NPT as catalogue options, and the bracket is included unless J is specified.
Flow is published as curves, not as one rated number, so ask us to confirm sizing from the datasheet against your application before ordering.
Quick checklist
- ✓ Body size for your peak flow (See datasheet here)
- ✓ Element 40 µm or 5 µm
- ✓ Drain sets the regulating band
- ✓ Gauge fitted, shape and scale
- ✓ Thread PT, G (BSPP) or NPT
- ✓ Oil needed downstream? Use GFC instead
Installation & Maintenance Notes
- check Mount vertically, bowl down, following the airflow arrow.
- check One body does the filtering and the regulating — no separate regulator needed.
- check Keep inlet pressure at or below 1.0 MPa (145 psi).
- check Adjust only within 0.15 - 0.9 MPa (20 - 130 psi).
- check Drain condensate before the bowl fills.
- check Keep the unit above freezing (-5 to +70 °C, unfreeze).
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
Airtac GFR Filter Regulator GFR300C10NW FAQ
AirTAC does not publish a single rated flow figure for the G series - performance is given as flow curves. Tell us your pressure and air demand and we will confirm the flow and sizing from the datasheet on request.
The W code selects the 5 um element for finer particle removal, for example ahead of compact valves, nozzles or spray equipment; the blank code's 40 um element is the standard grade for general machine air. Both grades, plus drain and thread options, are available across the GFR200-600 range.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac GFR Filter Regulator GFR300C10NW
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.