Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S
The AirTAC Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S is a genuine double acting, adjustable stroke standard round-body mini air cylinder with a Ø16mm bore and 35mm stroke, M5×0.8 air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service.
- BoreØ16 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting, adjustable stroke
- Rod threadM6×1.0
- CushionFixed anti-impact bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S
Where a machine builder wants maximum tuning freedom on a short stroke, the MAJ16X35-30S offers a 30 mm extend-trim window on a 16 mm bore and 35 mm nominal stroke - the stop screw can cut travel almost back to the bumper. Rated 100.5 N push at 0.5 MPa, it targets light gating, indexing and test positions.
The heterogeneous two-way piston seal traps grease inside the barrel, so the riveted stainless body runs long intervals without relubrication in dusty plant air. Treat 100.5 N as the ceiling: about 60 N of working force at 0.5 MPa keeps cycles crisp, equal to hoisting some 5 kg vertically with margin to spare. Sensors CMSG, DMSG and EMSG snap onto the standard-fit magnet.
Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S Technical Specifications
| Model | Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S |
|---|---|
| Series | MAJ mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 35 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed anti-impact bumper pads |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 101 N | 86 N |
| 0.7 MPa | 141 N | 121 N |
| Max (@1.0 MPa) | 21 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S
| MAJ | Standard round-body mini cylinder (adjustable-stroke). |
|---|---|
| 16 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S Is Used
Test-probe depth stop
Sets how deep an electrical probe tip reaches into a connector housing; the 30 mm range covers several housing heights.
Small-parts crimp check
Applies around 60 N at 0.5 MPa to verify a ribbon-cable crimp before the assembly passes downstream.
Tray lane gate on a pill sorter
Gates pill trays between lanes, with a CMSG switch confirming the gate is fully seated.
Is the Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S the Right Cylinder?
There is no smaller MAJ bore, so if 100.5 N at 0.5 MPa is marginal, the next step is the 20 mm bore at 157.0 N push. The generous 30 mm window suits prototypes and multi-product fixtures where the extend stop is reset between changeovers. Remember the stop fixes the end of travel only; it will not pin the rod against drifting when supply pressure fails. Mount on an FA flange or LB foot, or hang I / Y knuckles on the 6 mm rod.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Bumper models: keep speed within the rated range.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S FAQ
Forces: 100.5 N push and 86.4 N pull at 0.5 MPa; 140.7 N push and 120.9 N pull at 0.7 MPa; 20.5 kgf theoretical maximum at 1.0 MPa. Pressure spans 0.15-1.0 MPa (22-145 psi), proof is 1.5 MPa (215 psi), speed 30-800 mm/s, port size M5x0.8.
The stainless tube with a hard-chrome plated rod resists corrosion in wet, food-wash or outdoor corners where painted minis fail, and the riveted round body stays slim behind crowded fixtures. The fixed bumper pads simply soften stroke-end impact; adjustable cushioning belongs to the MACJ family.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ16X35-30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.