Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S
The AirTAC Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S is a genuine double acting, adjustable stroke standard round-body mini air cylinder with a Ø32mm bore and 5mm stroke, 1/8" air ports and a stainless-steel barrel with a hard-chrome-plated rod for reliable, mildly corrosion-resistant service.
- BoreØ32 mm
- Stroke5 mm
- Port size1/8"
- Acting typeDouble acting, adjustable stroke
- Rod threadM10×1.25
- CushionFixed anti-impact bumper pads
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S
Short travel, tight spot: the MAJ32X5-10S gives a 5 mm stroke on a bore 32 round-body mini that still pushes 402 N at 0.5 MPa, a force-to-footprint ratio most minis cannot match. The -10 window is wider than the stroke itself, so the extend stop can sit anywhere along the travel, set from the screw outside the cover.
Inside, a stainless barrel carries a hard-chrome 12 mm piston rod with a grease-storing two-way seal, and the aluminium covers are rolled on for a sealed riveted body. Fixed bumper pads soften each end of stroke; they decelerate, they do not cushion like the MACJ. On 0.15-1.0 MPa (22-145 psi) air at 30-800 mm/s, budget about 241 N (0.6 x 402 N) for the actual work.
Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S Technical Specifications
| Model | Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S |
|---|---|
| Series | MAJ mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 5 mm |
| Acting type | Double acting, adjustable stroke |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Fixed anti-impact bumper pads |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MA-series datasheet. Barrel: stainless-steel tube (round-body, riveted rolling-packed construction); piston rod: carbon steel with 20µm hard-chrome plating; covers: aluminium alloy. Thread options: PT (blank) / G / NPT. Every MA-series cylinder ships with a built-in magnet for CMSG / DMSG / EMSG position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S
| MAJ | Standard round-body mini cylinder (adjustable-stroke). |
|---|---|
| 32 | Bore size in mm. |
| ×5 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| -S | Built-in magnet for CMSG / DMSG / EMSG sensors (standard on MA series). |
| CA / U / CM | Back-cover type: CA pivot, U flat-end, CM round-end. |
MA-family variants: MA / MAC (double acting ±cushion), MSA / MTA (single acting push / pull), MAD / MACD (double rod ±cushion), MAJ / MACJ (adjustable stroke ±cushion), MAR (cushioned with integrated F/U mount). Mounting accessories: FA flange, LB foot, SDB pivot; plus I and Y knuckles. Thread PT (blank) / G / NPT.
Where the Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S Is Used
Micro-dose dispense push
A 5 mm extend advances a syringe barrel a fixed short distance in a lab filler; the 10 mm window trims dose travel without touching the plumbing.
Fixture pin clamp
Retracts a locating pin 5 mm on a welding jig, with 402 N at 0.5 MPa seating the pin hard against its taper every cycle.
Present-part kick trigger
Fires a 5 mm nudge that starts a part onto a vision-station belt, while a CMSG switch reports the extend position inside the 10 mm window.
Is the Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S the Right Cylinder?
At 402 N push and 346 N pull from 0.5 MPa, this bore 32 sits between bore 25 (245 N) and bore 40 (628 N); pick the smaller if the load stays under roughly 147 N, the larger once it passes about 241 N.
A 5 mm stroke rarely needs external guidance, but keep the rod square to the part so the stop screw seating stays repeatable. Choose FA or LB mounting and an I or Y rod knuckle, and set the extend limit anywhere inside the 10 mm window.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) is standard for sensors
- ✓ Back cover (CA/U/CM) & mount (FA/LB/SDB)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Bumper models: keep speed within the rated range.
- check Installation by qualified personnel per AirTAC docs.
Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S FAQ
Bore 32 gives 402 N push and 346 N pull at 0.5 MPa, and 563 N push with 484 N pull at 0.7 MPa; the theoretical peak is 82 kgf at 1.0 MPa. Run it on 0.15-1.0 MPa (22-145 psi) filtered air at 30-800 mm/s, with a 1/8" port.
No. Every MA-series cylinder ships with a built-in magnet as standard, so CMSG, DMSG and EMSG switches clip straight onto the barrel of the MAJ32X5-10S without a special piston or any waiting period.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MAJ Double Rod Adjustable Stainless Steel Mini Cylinder MAJ32X5-10S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.